September is here
Hotshot
Joined: Jun 2006
Posts: 15,450
Likes: 3
From: Hampstead, NC
Yeah, we pulled the carpet in there and replaced it with a floating laminate. Looked way better than old brown carpet.
Post Fiend
Joined: Jun 2014
Posts: 6,801
Likes: 7
From: DFW, TX-GoldCanyon, AZ
My carpeting is still in good shape, but I would rather do a laminate like you did... Any trick to get it under the lip of the living room slide?
Thread Starter
|
Fleet Owner
Joined: Mar 2003
Posts: 24,724
Likes: 74
From: Blue Hill Township
I think there are a few more this year but I won't be attending them.
Thread Starter
|
Fleet Owner
Joined: Mar 2003
Posts: 24,724
Likes: 74
From: Blue Hill Township
One GTO managed to ball it up through the fence and down into the weeds. Oops...
If I was to consider open track or longer runs in the Mustang I think I would need to look into adding an oil cooler. I could see the oil pressure down a bit as the oil got hot.
Post Fiend
Joined: Jun 2014
Posts: 6,801
Likes: 7
From: DFW, TX-GoldCanyon, AZ
Every time something like that happens (car through the fence etc), the facility has a knee jerk reaction to suspend all events for a period.. I've seen that happen both at St Cloud as well as DCTC .... Shame that someone had to screw it up!!!
I used to always use these adapters from Canton.. Really well made and never had any leaks. I ran a remote filter and the cooler off of this adapter. I suggest -10 or -12 lines. Don't even think of running -8 as there is too much restriction..
http://www.summitracing.com/parts/ct...MobileSwitchNo
I used to always use these adapters from Canton.. Really well made and never had any leaks. I ran a remote filter and the cooler off of this adapter. I suggest -10 or -12 lines. Don't even think of running -8 as there is too much restriction..
http://www.summitracing.com/parts/ct...MobileSwitchNo
Post Fiend
Joined: Jun 2014
Posts: 6,801
Likes: 7
From: DFW, TX-GoldCanyon, AZ
Oops.. This is the correct part if you want a remote oil filter.& cooler..
http://www.summitracing.com/parts/ct...ions/make/ford
http://www.summitracing.com/parts/ct...ions/make/ford
Lead Driver
Joined: Apr 2003
Posts: 9,965
Likes: 1
From: H-town, MN
Anybody willing to pick this up for me? I can't get down there until tomorrow evening and guessing it will be sold by then.
https://minneapolis.craigslist.org/d...222214554.html
https://minneapolis.craigslist.org/d...222214554.html
FTE Stories
Ford Trucks for Ford Truck Enthusiasts
Top 6 Best Deals Available on New Fords & Lincolns Right Now
Brett Foote
This Hennessey Takes the Expedition Tremor's Off-Roading Capability to the Next Level
Verdad Gallardo
Top 10 Fords at 2026 Carlisle Ford Nationals
Joe Kucinski
3 Best / 3 Worst Parts of Modern Ford Ownership
Brett Foote
10 Amazing Upgrades That Solve Common Ford Truck Owner Headaches
Pouria Savadkouei
Every 2026 Ford Engine Explained
Brett Foote
10 Ugly Ford Trucks That We Still Kinda Love
Joe Kucinski
10 Things Every Truck Owner NEEDS (2026 Edition)
Michael S. Palmer
Rezvani's Latest Post-Apocalyptic Monster Is a Ford F-150 Raptor Underneath
Verdad Gallardo
FTE Chapter Leader
Joined: Mar 2005
Posts: 23,869
Likes: 9
From: Suppertown, MN
Good morning MN FTE!
Went to Sauk Centre this morning to look at a '06 F350 that needed some TLC and I could get cheap. Turned out to be a lot tougher shape then I wanted to tackle for the price and still be able to make a buck or two after selling it. Oh well........
Went to Sauk Centre this morning to look at a '06 F350 that needed some TLC and I could get cheap. Turned out to be a lot tougher shape then I wanted to tackle for the price and still be able to make a buck or two after selling it. Oh well........
Hotshot
Joined: Jun 2006
Posts: 15,450
Likes: 3
From: Hampstead, NC
I simply pulled the slide in just a bit to get it up off the floor. It wasn't to bad then. However, stay good and thin on the material. There is very little clearance between the floor and bottom of the slide.
FTE Chapter Leader
Joined: Mar 2005
Posts: 23,869
Likes: 9
From: Suppertown, MN
Yep and I just got a call back on it and he dropped another 1000 bucks off the price. I told him he still had to go lower like another 1000 lower so I will let him stew on that a while and get back to me.
Lead Driver
Joined: Apr 2003
Posts: 9,965
Likes: 1
From: H-town, MN
