ingnition switch problem
Thread Starter
|
Senior User
Joined: Jun 2012
Posts: 129
Likes: 0
ingnition switch problem
I took my dash apart recently in order to install my aftermarket a/c kit and to paint the dash. While back there pulling everything out, I pulled the ignition assembly off. I was not aware of the trick to use a paper clip and the key to remove it properly. At any rate, the piece came off pretty easily, however, three copper springs and retainers popped out as well. Not aware of what I did or how to put everything back together. I'm pretty sure the springs go in the black plastic piece with the retainers on top, but have no idea if that's all I need to do and how it snaps back together. Any tips, instructions, thoughts (besides the fact that I'm an idiot, LOL)? I could not find anything through searching, or in my Hayne's manual. Thanks.
Hotshot
Joined: Apr 2009
Posts: 14,333
Likes: 247
From: Stanley, VA
You might have to replace the ignition switch. Normally when you remove the lock cylinder from the ignition switch there are only two parts, the lock cylinder and the switch body. I don't think there are supposed to be any spare parts.
Thread Starter
|
Senior User
Joined: Jun 2012
Posts: 129
Likes: 0
If I have to replace the ignition it's no big deal. I would like to retain the same key for the door locks. Can I take the new ignition to a locksmith with my current key to have it keyed appropriately? Thanks.
Cargo Master
Joined: Apr 2009
Posts: 3,038
Likes: 4
From: South west Idaho
You probably can,but you can buy new locks and ignition cylinder for about the same cost. I just did that with mine as my locks were getting worn and i only wanted one key. It may be different in your area though . The switch was being sold with out the key cylinder , so i went that way.
Thread Starter
|
Senior User
Joined: Jun 2012
Posts: 129
Likes: 0
You probably can,but you can buy new locks and ignition cylinder for about the same cost. I just did that with mine as my locks were getting worn and i only wanted one key. It may be different in your area though . The switch was being sold with out the key cylinder , so i went that way.
So I really just need to buy the new ignition and can keep my key cylinder, right? Good. I'll just do that. Thanks.
Cargo Master
Joined: Apr 2009
Posts: 3,038
Likes: 4
From: South west Idaho
Trending Topics
More Turbo
Joined: Jul 2010
Posts: 653
Likes: 2
From: Concord, NC
A little tricky is right. I think I would rather set the engine in again, rather than put that ignition switch in twice. I was particular about using the same switch/key since it was Pop's Truck, but if that were not the case, I would have just replaced everything at the drop of a hat.
FTE Stories
Ford Trucks for Ford Truck Enthusiasts
10 Things Every Truck Owner NEEDS (2026 Edition)
Michael S. Palmer
Rezvani's Latest Post-Apocalyptic Monster Is a Ford F-150 Raptor Underneath
Verdad Gallardo
Top 10 Most Expensive Ford Trucks Ever Sold on Bring a Trailer
Joe Kucinski
2027 Ford Super Duty Buyer's Guide (Every Model, Engine, & Package)
Brett Foote
Top 10 Ford Truck Tragedies
Joe Kucinski
AEV FXL Super Duty - the Super Duty Raptor Ford Doesn't Make
Brett Foote
Lobo Vs Lobo: Proof the F-150 Lobo Should Be Even Lower!
Michael S. Palmer
Ford's 2001 Explorer Sportsman Concept Looks For a New Home
Verdad Gallardo
10 Best Ford Truck Engines We Miss the Most!
Joe Kucinski
Thread
Thread Starter
Forum
Replies
Last Post
mr.badwrench
1961 - 1966 F-100 & Larger F-Series Trucks
9
Jun 4, 2018 11:10 AM
RedBoat
Explorer, Sport Trac, Mountaineer & Aviator
6
Jun 27, 2006 04:18 PM
mositso
1973 - 1979 F-100 & Larger F-Series Trucks
3
Oct 14, 2004 12:47 PM
