Hedman Headers
Thread Starter
|
Junior User
Joined: Apr 2005
Posts: 56
Likes: 0
Hedman Headers
I have a 79 F-250 4x4 with a 351M and the NP435/205 combination. I've rebuilt the engine and I'm about ready to put it in, but I'm trying to decide between stock manifolds and the Hedman Elite 89218 headers.
I understand that the collectors come out fairly close to the transmission crossmember. Hedman's instructions suggest routing the drivers' pipe down under the crossmember. I have the dual tanks, and I would prefer to run a single 3" pipe back.
Is there room to cross the driver's side exhaust over to the passenger side in front of the crossmember? From there, I'd like to duplicate the factory pipe routing between the crossmember and the cab. I have no exhaust on the truck whatsoever, so connecting with an existing pipe is not a concern.
Is it possible and practical to do what I want here? Does anyone have pictures of the underside of their truck showing how they made a y-pipe?
Thanks.
I understand that the collectors come out fairly close to the transmission crossmember. Hedman's instructions suggest routing the drivers' pipe down under the crossmember. I have the dual tanks, and I would prefer to run a single 3" pipe back.
Is there room to cross the driver's side exhaust over to the passenger side in front of the crossmember? From there, I'd like to duplicate the factory pipe routing between the crossmember and the cab. I have no exhaust on the truck whatsoever, so connecting with an existing pipe is not a concern.
Is it possible and practical to do what I want here? Does anyone have pictures of the underside of their truck showing how they made a y-pipe?
Thanks.
Post Fiend
Joined: Mar 2005
Posts: 8,542
Likes: 5
From: Louisiana
I don't have the headman headers, but I just put on some summit headers and put on duals. When I finished installing the headers, there wasn't much room for anything.
IF you made a 90 degree turn right after the header, you might be able to fit it inbetween the header and the crossmember, but not likely.
I much rather headers over exhasut manafolds anyday.
IF you made a 90 degree turn right after the header, you might be able to fit it inbetween the header and the crossmember, but not likely.
I much rather headers over exhasut manafolds anyday.
Senior User
Joined: Oct 2005
Posts: 271
Likes: 0
From: Gresham Oregon
I'd also like to know too, I'm in the same boat looking at exhaust options. Hooker makes a exhaust kit for headers and manifolds for the factory routing. Summit carries them and I think the kit minus headers and muffler is about $220. Hedman also make an elite header for fenderwell exit, but then the exhaust is on the outside of the frame rail, some people like that, some don't.
Thread Starter
|
Junior User
Joined: Apr 2005
Posts: 56
Likes: 0
Originally Posted by Jmudder79
Why don't you get outside the frame headers. They make exhaust hookup easy. Just some straight pipe and a muffler. No bends. I did mine in my driveway.
Junior User
Joined: Jun 2003
Posts: 87
Likes: 0
I was also thinking of running fenderwell exit headers but was conserned that running 38" tires would rub on the headers. Has anyone ran 38s and had this happen?
Trending Topics
Post Fiend
Joined: Mar 2005
Posts: 8,542
Likes: 5
From: Louisiana
Plowdude, there are a few guys on here running fenderwell exit headers and 44s. They don't have any problems, so I'm sure you'd be fine.
FTE Stories
Ford Trucks for Ford Truck Enthusiasts
Rezvani's Latest Post-Apocalytic Monster Is a Ford F-150 Raptor Underneath
Verdad Gallardo
Top 10 Most Expensive Ford Trucks Ever Sold on Bring a Trailer
Joe Kucinski
2027 Ford Super Duty Buyer's Guide (Every Model, Engine, & Package)
Brett Foote
Top 10 Ford Truck Tragedies
Joe Kucinski
AEV FXL Super Duty - the Super Duty Raptor Ford Doesn't Make
Brett Foote
Lobo Vs Lobo: Proof the F-150 Lobo Should Be Even Lower!
Michael S. Palmer
Ford's 2001 Explorer Sportsman Concept Looks For a New Home
Verdad Gallardo
10 Best Ford Truck Engines We Miss the Most!
Joe Kucinski
2026 Shelby F-150 Off-Road: Better Than a Raptor R?
Brett Foote
Senior User
Joined: Jun 2001
Posts: 480
Likes: 0
From: Alabama
i have a 2wd 460 with headers and my driver side crossed under the trans. just behind the bell housing. The first x-member that goes from the radius bushings was notched as well for clearance. then dual exhaust down the passenger side (dual tanks also) and the one side shoots over right before axle to have both pipes exit out the back .
Elder User
Joined: Feb 2006
Posts: 694
Likes: 1
From: New Gretna, New Jersey
Originally Posted by Plowdude
I was also thinking of running fenderwell exit headers but was conserned that running 38" tires would rub on the headers. Has anyone ran 38s and had this happen?
Thread
Thread Starter
Forum
Replies
Last Post
grandpas1974
1973 - 1979 F-100 & Larger F-Series Trucks
3
Apr 23, 2015 05:07 AM
Bootlegger's Deluxe
Ford Inline Six, 200, 250, 4.9L / 300
32
Jan 30, 2011 12:30 AM
djangoism
1973 - 1979 F-100 & Larger F-Series Trucks
18
Dec 1, 2009 12:49 PM
turbocoupe5.0
Big Block V8 - 385 Series (6.1/370, 7.0/429, 7.5/460)
5
Dec 27, 2005 02:17 PM
