Just listed a NOS pair of grille guard braces for 53-56 trucks on eBay. Pm me if you need them.

 

239 ohv motor for parts
complete rear axle
Complete front axle assy including steering components.
Gimme an offer I can't refuse and they're yours.
I'm tired of tripping over these.

John

 

Hello Mark,
I am interested in the Chassis & engine & driveline.
If I read the ad correctly, it is a F-600, 1956 unit - correct?
Is the engine turn?
Any idea on the Y-block miles?
If we come to an agreement & I pay you now - can I pick it up when the weather clears?

Thank you.
Marty
C. # 773-490-9747

 

Hi Marty:
It is a C600, 1956- COE. I WILL CALL YOU this afternoon, and answer any questions you may have.
Regards, Mark

 

This is not me/mine but while looking around for new wheels to replace my "roadside IED" dreaded widowmakers I tripped over this. My original 49 flathead is long gone, but somebody else here may have good block to bolt these to, or need some of the parts anyway?

https://albuquerque.craigslist.org/p...585195128.html

 

NEW PRICE! If you previously tried to message me about this please try again. I wasn't aware my inbox was full.
1954 F100 with powder coated TCI chassis. Upgraded 12” Wilwood brakes; prebent hardlines. Great start to a project for someone to make their own. Cab and door alignment is super solid. Was planning to replace the firewall so that will need attention.
-Front tilt kit.
-Extra pair of doors.
-Currie 3.70 posi
-Bench seat frame is perfect.
-Setup for AOD
-All glass aside from rear piece.
-Multiple totes of parts.
-Decent bed available. With the snowy weather haven't had a chance to get to my storage unit. Will soon be available.
Please contact me with questions. 24’ aluminum trailer available if interested as well.
Located in Sioux Falls, SD
NEW PRICE: $17,500OBO $18,500

 

For Sale -- 1952 - 1954 215/223 complete distributor p/n FAA-12127-C. Nice condition, no rust inside (desert SW part). Vacuum advance responds to vacuum but may leak. Has points and condenser, condition unknown. Cap is decent. $20 + shipping.

 

Just got this today. I could have sworn someone was looking for a fuel tank but I can find the post.


RockAuto.com

 

I'm looking for LH/RH spear/disc 52 F-1 moldings, don't have to be perfect condition as long as nothing missing. Also looking for original horns, and hood support rod.

If you can help I will cover packaging and shipping to UK (including duty/tax).

 

Complete 239 ohv motor carb to pan unfortunately locked I believe. Offers? Complete front and rear axles from same vehicleDrum to drum Hate to scrap this if anyone can use some or all.250 obo TIA John

 

I have this old F3 i'm looking to sell if that would help you any.
Good patina.

Thanks
Timm
214 769-1150

 

I am cleaning out the garage and ran across these from my 7HA 226 H engine rebuild. Two piston sets, one 0.010", the other 0.030", connecting rods, bearing caps, and timing cover. I am keeping the balancer.

 

56 F1 hood in good shape..900 new..$550 or best offer
56 F1 drivers door in very nice shape..$250.00
Pair of bed sides..no dents just surface rust...150.00
Fender for 48 or 49 F1..125.00..More pics available. Located outside Buffalo NY text or call 716-440-7089..NOT after 930PM EST as I retire early I also have an dash ashtray and interior mirror

 

Hey looking for a 1950 ford truck drivers window as mine cracked up bad over the winter as water got in the gap from the peeling plastic saftey liner and froze

 

I only have the door. A glass place may cut a piece for You