maf sensor
Elder User
Joined: Jan 2002
Posts: 555
Likes: 0
maf sensor
That may be hard to test without a Ford shop manual. The boys that worked at the Ford dealer near me always laughed at us and said that the best way to test a sensor was to install a known good one. They always had extra ones on hand..very lucky!
All kidding aside.....Not a lot you can do without some equipment and or check for codes to see if it shows up. Make sure it has vacuum.
All kidding aside.....Not a lot you can do without some equipment and or check for codes to see if it shows up. Make sure it has vacuum.
Thread Starter
|
Junior User
Joined: Dec 2001
Posts: 66
Likes: 0
maf sensor
nope it is mas air , air flow sensor is right after the air filter box it has a wire connection going to it , following air flow sensor is a y junction with 2 hoses going into the throttle boby
Posting Guru
Joined: Dec 1999
Posts: 1,903
Likes: 2
From: Copley, OH
maf sensor
Ford used MAF on some 94 and 95 302s, don't remember or much care which. 300s didnt get MAF till 96, not sure when the standard 351s made the transition, the 96s were MAF for sure though.
Trending Topics
Freshman User
Joined: Mar 2002
Posts: 39
Likes: 0
From: Front Royal, VA
FTE Stories
Ford Trucks for Ford Truck Enthusiasts
Top 10 Most Expensive Ford Trucks Ever Sold on Bring a Trailer
Joe Kucinski
2027 Ford Super Duty Buyer's Guide (Every Model, Engine, & Package)
Brett Foote
Top 10 Ford Truck Tragedies
Joe Kucinski
AEV FXL Super Duty - the Super Duty Raptor Ford Doesn't Make
Brett Foote
Lobo Vs Lobo: Proof the F-150 Lobo Should Be Even Lower!
Michael S. Palmer
Ford's 2001 Explorer Sportsman Concept Looks For a New Home
Verdad Gallardo
10 Best Ford Truck Engines We Miss the Most!
Joe Kucinski
2026 Shelby F-150 Off-Road: Better Than a Raptor R?
Brett Foote
2027 Super Duty Carhartt Package First Look: 12 Things You NEED to Know!
Michael S. Palmer
Post Fiend
Joined: Jan 2000
Posts: 5,860
Likes: 4
From: Metro Detroit (Redford)
maf sensor
>300s didnt get MAF till 96
I have a '95 300 I6 and was concerned about over oiling my K&N filter causing the MAF to go haywire, but if I have speed density do I need to be concerned?
I have a '95 300 I6 and was concerned about over oiling my K&N filter causing the MAF to go haywire, but if I have speed density do I need to be concerned?
Post Fiend
Joined: Jan 2000
Posts: 5,860
Likes: 4
From: Metro Detroit (Redford)
maf sensor
Thanks Sprocket. I called K&N and they told me what was in the other post, that if I have two tubes coming out of my air box it is speed density. But they didn't know if excess oil would be a problem for that. Anyway I am letting my K&N sit on some rags for a few days while the oil drips out of the rubber ends where the pleats seal in. No oil dripped from the gauze area (though I sprayed it about 10 times on each side).
Thread
Thread Starter
Forum
Replies
Last Post
bflo1220
Explorer, Sport Trac, Mountaineer & Aviator
1
Jan 29, 2015 06:46 AM
gman97005
Small Block V8 (221, 260, 289, 5.0/302, 5.8/351W)
1
Oct 25, 2013 03:38 AM
