Aligning doors
Thread Starter
|
Junior User
Joined: Jul 2004
Posts: 75
Likes: 1
From: Oromocto, NB
Aligning doors
Hi there. Just about finish welding in new lower door pillars and step plates. Is there an easy way or procedure in aligning the doors so they close properly or is it a trial and error thing? Mind you, i'm using different doors than the original ones. Thanks!
Postmaster
Joined: Nov 2001
Posts: 3,351
Likes: 1
From: Escondido, CA
It's pretty much a trial and error process. Having plastic wedges to place in key areas does help with minor adjustment though. Like the top and bottom, and the back upper and lower portions of the door. The stricker plate is what took me the longest to adjust to be honest. I was tired of the doors needing to be slammed. Now as long as the door is swung it will latch and not rattle.
Tuned
Joined: Jul 2004
Posts: 413
Likes: 0
This may be too late for you, but maybe others can benefit. I saw a trick on MuscleCar where the guy drilled small holes in the hinges (once aligned or pre- disassembly). He re-aligned after assembly using the small holes as guides
Lead Driver
Joined: Aug 2003
Posts: 6,305
Likes: 18
From: Boulder Creek, Ca
Probably goes w/out saying, if hav'nt replaced weather strip, and intend to do so in future, suggest doing it now. Keep in mind, can be pain in backside w/ new rubber and may require occasional adjustment until seated. As noted, matter of trial and error. May try removing striker plate, with another person inside, set door in desired position then have person inside tighten hinge bolts. Use caution so fender and door do not bind while testing. Once close, mark for reference than fine tune. Torque on bolts around 45 ft. lbs. For striker plate it's the same, once close mark position then fine tune in small increments. Torque on screws 12-15 ft. lbs. Anyhow, good luck.
dave
dave
Trending Topics
Postmaster
Joined: Dec 2003
Posts: 4,423
Likes: 8
From: Clarksville,Tn
This may be too late for you, but maybe others can benefit. I saw a trick on MuscleCar where the guy drilled small holes in the hinges (once aligned or pre- disassembly). He re-aligned after assembly using the small holes as guides
I'm alittle late on this post; but thought I would also mention the above techinque is a great pre-disassembly when removing the hood and a trunk lid as well.
Mitch
I'm alittle late on this post; but thought I would also mention the above techinque is a great pre-disassembly when removing the hood and a trunk lid as well.
Mitch
FTE Stories
Ford Trucks for Ford Truck Enthusiasts
10 Things Every Truck Owner NEEDS (2026 Edition)
Michael S. Palmer
Rezvani's Latest Post-Apocalyptic Monster Is a Ford F-150 Raptor Underneath
Verdad Gallardo
Top 10 Most Expensive Ford Trucks Ever Sold on Bring a Trailer
Joe Kucinski
2027 Ford Super Duty Buyer's Guide (Every Model, Engine, & Package)
Brett Foote
Top 10 Ford Truck Tragedies
Joe Kucinski
AEV FXL Super Duty - the Super Duty Raptor Ford Doesn't Make
Brett Foote
Lobo Vs Lobo: Proof the F-150 Lobo Should Be Even Lower!
Michael S. Palmer
Ford's 2001 Explorer Sportsman Concept Looks For a New Home
Verdad Gallardo
10 Best Ford Truck Engines We Miss the Most!
Joe Kucinski
Postmaster
Joined: Dec 2003
Posts: 4,423
Likes: 8
From: Clarksville,Tn
Airharley;
Well; I'm sorry my computer skill are lacking; I try to cut & paste his comment to add my additionally comment to his. I was only trying to add to his post too allow others to understand that; that techinque can apply to the hood & trunk lids as well.
Have a great day.....
Mitch
Well; I'm sorry my computer skill are lacking; I try to cut & paste his comment to add my additionally comment to his. I was only trying to add to his post too allow others to understand that; that techinque can apply to the hood & trunk lids as well.
Have a great day.....
Mitch
Thread
Thread Starter
Forum
Replies
Last Post
nikmish
1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks
20
Dec 3, 2014 07:21 AM
NBC-Steve
1973 - 1979 F-100 & Larger F-Series Trucks
9
Dec 25, 2012 09:18 PM