balljoints
Thread Starter
|
More Turbo
Joined: May 2005
Posts: 704
Likes: 2
From: Thousand Oaks, CA
balljoints
this last weekend i went with some friends to the sand dunes to go dirt bike riding and at the end of the weekend i had to pull my friends truck and trailer out of the sand.
my friends were watching and noticed that my front wheels were shaking right to left. i noticed there was a lot of shaking in the steering wheel also. my question is could this be due to bad balljoints or maybe the steering stabalizer? i have 63,000 mikes on the truck, is this a common thing? thanks guys.
my friends were watching and noticed that my front wheels were shaking right to left. i noticed there was a lot of shaking in the steering wheel also. my question is could this be due to bad balljoints or maybe the steering stabalizer? i have 63,000 mikes on the truck, is this a common thing? thanks guys.
Postmaster
Joined: Nov 2004
Posts: 2,854
Likes: 0
From: New Hampshire
kwik is probably right, but, the stock ball joints on the newer superduties are JUNK...! they are sealed so you can't grease them... i have to replace mine this month... there's another big bill on the card..! i guess that means no new mods for me this month..!
Thread Starter
|
More Turbo
Joined: May 2005
Posts: 704
Likes: 2
From: Thousand Oaks, CA
Originally Posted by johnny8
kwik is probably right, but, the stock ball joints on the newer superduties are JUNK...! they are sealed so you can't grease them... i have to replace mine this month... there's another big bill on the card..! i guess that means no new mods for me this month..!
Postmaster
Joined: Nov 2004
Posts: 2,854
Likes: 0
From: New Hampshire
i do not know the brand... but they are servicable... i.e. greaseable... i was told by my mechanic that if i keep the ones that he is putting in greased i will never have to replace them... i do know that the ones that were in my truck when i bought it were the oem type and had just been replaced... they didn't last long...
New User
Joined: Apr 2004
Posts: 13
Likes: 0
From: Chesapeake Va.
I had to replace my about two months ago. I used the greasable ones. I got mine from Napa I think I paid $250 for all four. I replaced them myself not that much of a problem just use a bigger hammer to get them out. The biggest problem I had was replacing the knuckle/axle seal. After I destroyed two of them I brought the shafts to a Ford mechanic to install the seals. The seals were $35 apiece and the only place to get them was the dealer.
Erick
Erick
Mountain Pass
Joined: Nov 2003
Posts: 236
Likes: 1
From: Central Ky.
Trending Topics
Thread Starter
|
More Turbo
Joined: May 2005
Posts: 704
Likes: 2
From: Thousand Oaks, CA
thanks guys for all the input, i guess i know what i am going to do with my next paycheck.
do i just replace the 4 balljoints at the knuckles? or should i replace the balljoints in the steering too?
do i just replace the 4 balljoints at the knuckles? or should i replace the balljoints in the steering too?
FTE Stories
Ford Trucks for Ford Truck Enthusiasts
Top 10 Most Expensive Ford Trucks Ever Sold on Bring a Trailer
Joe Kucinski
2027 Ford Super Duty Buyer's Guide (Every Model, Engine, & Package)
Brett Foote
Top 10 Ford Truck Tragedies
Joe Kucinski
AEV FXL Super Duty - the Super Duty Raptor Ford Doesn't Make
Brett Foote
Lobo Vs Lobo: Proof the F-150 Lobo Should Be Even Lower!
Michael S. Palmer
Ford's 2001 Explorer Sportsman Concept Looks For a New Home
Verdad Gallardo
10 Best Ford Truck Engines We Miss the Most!
Joe Kucinski
2026 Shelby F-150 Off-Road: Better Than a Raptor R?
Brett Foote