300 6 rebuild
Thread Starter
|
Mountain Pass
Joined: Apr 2004
Posts: 132
Likes: 1
From: Montana
300 6 rebuild
I am planning on rebuilding my 300. It is in a 77 p/u with a c4 and 3:07 dana 44 rear end.
Anyway I want to get another 100 hp out of it. What things would I need to do in order to do this and are there turnkey motors out there that sell such an animal? Do any of the sponsors have parts that I can use?
Any advice will be greatly appreciated.
Anyway I want to get another 100 hp out of it. What things would I need to do in order to do this and are there turnkey motors out there that sell such an animal? Do any of the sponsors have parts that I can use?
Any advice will be greatly appreciated.
Postmaster
Joined: Apr 2000
Posts: 3,890
Likes: 10
From: La Verne, California
This is what Don Johnson of Johnson Machine Service Racing Engines, founded over 45 years ago, did for me.
300 H.P. @ 4600 rpm & 400 Torque @ 3200 rpm w/ a 10 to 1 C.R.
It idels @ 675 & is smooth as glass, a quarter was placed on top of the Valve Cover & it Did Not move Nor rattle.
Ross Pistons 4.060
Hastings Power Flex Rings .060
Federal Mogul Mains .020 Under
Clevite Performance Bearings Std.
Federal Mogul Cam Bearings Std.
Melling Torque Cam
Melling H.V. Oli Pump
Eagle H-beam Rods 6.300 2.100 Rod Journal
Crane Gold Race Roller rockers
ARP Main Stud Kit, Rocker Studs,
Fisher International Ballancer
Bore 4.060
Power Hone 4.060
Full P&P Intake & Exhaust
Performance valve job
Performance Balance job on Steele Crank w/ in 7 grams
Grind Rod Journals to 2.100
Plumb Intake for Heat via Water Pump
Deck Block to Square
Align hone to Factory specs
Deck block for Zero Deck
Offenhauser C Intake
Holley 1850 600 CFM
S.S. Borla 2 into 2 Header
Go here in this Forum & Scroll down 1/2 & 3/4s of the way down to view Pix of my 300 I-6.
https://www.ford-trucks.com/forums/s...light=flashman
300 H.P. @ 4600 rpm & 400 Torque @ 3200 rpm w/ a 10 to 1 C.R.
It idels @ 675 & is smooth as glass, a quarter was placed on top of the Valve Cover & it Did Not move Nor rattle.
Ross Pistons 4.060
Hastings Power Flex Rings .060
Federal Mogul Mains .020 Under
Clevite Performance Bearings Std.
Federal Mogul Cam Bearings Std.
Melling Torque Cam
Melling H.V. Oli Pump
Eagle H-beam Rods 6.300 2.100 Rod Journal
Crane Gold Race Roller rockers
ARP Main Stud Kit, Rocker Studs,
Fisher International Ballancer
Bore 4.060
Power Hone 4.060
Full P&P Intake & Exhaust
Performance valve job
Performance Balance job on Steele Crank w/ in 7 grams
Grind Rod Journals to 2.100
Plumb Intake for Heat via Water Pump
Deck Block to Square
Align hone to Factory specs
Deck block for Zero Deck
Offenhauser C Intake
Holley 1850 600 CFM
S.S. Borla 2 into 2 Header
Go here in this Forum & Scroll down 1/2 & 3/4s of the way down to view Pix of my 300 I-6.
https://www.ford-trucks.com/forums/s...light=flashman
Last edited by Col Flashman; Jan 23, 2005 at 11:32 PM.
Thread
Thread Starter
Forum
Replies
Last Post
Caveman2851
Ford Inline Six, 200, 250, 4.9L / 300
12
Apr 28, 2020 03:02 PM
jmc0369
Ford Inline Six, 200, 250, 4.9L / 300
3
Jun 21, 2010 09:25 AM
paintman
Performance & General Engine Building
3
Jun 12, 2003 07:39 PM
