Axle casing differences
Thread Starter
|
New User
Joined: Apr 2015
Posts: 5
Likes: 0
Axle casing differences
Looked through some threads and couldn’t find much so figured I’d see if anyone could help.
My rear end differential (2008 F250 3.73 LS) and pretty much who rear end needs to be replaced I do have a replacement but it is extremely rusted out and needs new wheel bearings. This past weekend we just pulled the rear end out of my buddy’s truck (2011 F350 3.55 w/ elocker)and swapped in a pretty much new rear end from a 2018 that we found for a good deal. Basically my question is are the differential casings the same and will I will able to swap out everything from my good parts diff into the 2011 casing. Mostly just the pinion is what I n is is different as the 2011 one is much larger.
My rear end differential (2008 F250 3.73 LS) and pretty much who rear end needs to be replaced I do have a replacement but it is extremely rusted out and needs new wheel bearings. This past weekend we just pulled the rear end out of my buddy’s truck (2011 F350 3.55 w/ elocker)and swapped in a pretty much new rear end from a 2018 that we found for a good deal. Basically my question is are the differential casings the same and will I will able to swap out everything from my good parts diff into the 2011 casing. Mostly just the pinion is what I n is is different as the 2011 one is much larger.
Post Fiend
Joined: Nov 2001
Posts: 6,748
Likes: 118
From: Tallassee, ALabama
When you say the "pinion is much larger", are you talking about the diameter of the teeth or the shaft or what? The diameter of the pinion teeth will vary depending on the gear ratio. What ration is your rear end? What is the ratio of the 2011 rear end?
Hotshot
Joined: Oct 2006
Posts: 10,145
Likes: 7,971
From: Texas
Looked through some threads and couldn’t find much so figured I’d see if anyone could help.
My rear end differential (2008 F250 3.73 LS) and pretty much who rear end needs to be replaced I do have a replacement but it is extremely rusted out and needs new wheel bearings. This past weekend we just pulled the rear end out of my buddy’s truck (2011 F350 3.55 w/ elocker)and swapped in a pretty much new rear end from a 2018 that we found for a good deal. Basically my question is are the differential casings the same and will I will able to swap out everything from my good parts diff into the 2011 casing. Mostly just the pinion is what I n is is different as the 2011 one is much larger.
My rear end differential (2008 F250 3.73 LS) and pretty much who rear end needs to be replaced I do have a replacement but it is extremely rusted out and needs new wheel bearings. This past weekend we just pulled the rear end out of my buddy’s truck (2011 F350 3.55 w/ elocker)and swapped in a pretty much new rear end from a 2018 that we found for a good deal. Basically my question is are the differential casings the same and will I will able to swap out everything from my good parts diff into the 2011 casing. Mostly just the pinion is what I n is is different as the 2011 one is much larger.
The way your post sounds to me, you are also asking if the carrier ONLY can be swapped.......NO....both the pinion and the carrier must be swapped together. The ring and pinion are ALWAYS matched sets. Please clarify.
Cargo Master
Joined: Dec 2015
Posts: 2,912
Likes: 506
By pinion I'm guessing he means yoke.
I'm ASSuming the 10.5 uses a crush sleeve like the 10.25. I wouldn't go zipping off any pinion nuts without some research and an inch lb torque wrench...
There may be a crossover u-joint
I'm ASSuming the 10.5 uses a crush sleeve like the 10.25. I wouldn't go zipping off any pinion nuts without some research and an inch lb torque wrench...
There may be a crossover u-joint
Thread
Thread Starter
Forum
Replies
Last Post
joe_13894
1994.5 - 1997 7.3L Power Stroke Diesel
4
Feb 1, 2012 09:58 AM
