Tuner, programer recommendations
Thread Starter
|
Junior User
Joined: Dec 2010
Posts: 95
Likes: 0
From: North Ga.
Tuner, programer recommendations
Hello, I currently have a dp f6 chip, it is o k, but I would like to do more, I want a system that will allow me to run other peoples programs, e-mail capability of tunes, switch on the fly,with a digital readout of which tune I am in, like the f6 switcher, like the Hydra, and in the future as I learn try a few tweaks of my own, Jody says on his videos that he has a quarter horse emulator hooked to the pcm, I know very little about it, please inform, for now I want a platform that can be upgraded as my knowledge grows, and not double spending anymore, I know we have no idea about what the future holds as far as what will be available, I just want to make an informed decision, also I have read posts of tuner forums, looked, but could not find, ideas on that also?
Thank you
Thank you
Last edited by reality_check; Jan 22, 2013 at 06:10 PM. Reason: took out 2 -10s
Elder User
Joined: Jan 2012
Posts: 695
Likes: 1
From: Littleton, CO
The DP Tuner chip is proprietary - Only they can do your tunes.
If you want a Chip to run other tunes - You'll need to switch to a Ts style chip - but you will still need to pull your chip or bring it to a local shop that can flash tunes to that chip.
Otherwise, you'll be looking at a Tuner like the SCT Livewire that people can email you tunes much more quickly.
Creating your own tunes?
Bit of a risky idea (IMO). There's a couple flash programmers for the Ts Chips on ebay. But trying to learn fuel delivery, timing curves, etc etc is not something you just instantly pick up.
As I tell some people I work with - computers can be more of an art than science sometimes.
I don't know if i'd want to 'experiment' like that on a pretty expensive engine.
If you want a Chip to run other tunes - You'll need to switch to a Ts style chip - but you will still need to pull your chip or bring it to a local shop that can flash tunes to that chip.
Otherwise, you'll be looking at a Tuner like the SCT Livewire that people can email you tunes much more quickly.
Creating your own tunes?
Bit of a risky idea (IMO). There's a couple flash programmers for the Ts Chips on ebay. But trying to learn fuel delivery, timing curves, etc etc is not something you just instantly pick up.
As I tell some people I work with - computers can be more of an art than science sometimes.
I don't know if i'd want to 'experiment' like that on a pretty expensive engine.
Thread Starter
|
Junior User
Joined: Dec 2010
Posts: 95
Likes: 0
From: North Ga.
I don't plan on being able to write a custom tune right off the bat, but everybody started somewhere, either taking knowledge learned from another source, and applying it, apprenticing with a tuner, etc. I read a post where the poster was learning by trial, and error, like stated above , kinda risky, I will run tried and true tunes from top tuners, but just want to tinker with a stock tune at some point in the future, when that time comes, I don't want to have to buy jet another piece of hardware, all I am asking is what is the best frame work of hardware, and software, to achieve my goals, and find out what, how, or if an emulator will benefit me, can the emulator be ran instead of a chip?
Elder User
Joined: Jan 2012
Posts: 695
Likes: 1
From: Littleton, CO
I don't plan on being able to write a custom tune right off the bat, but everybody started somewhere, either taking knowledge learned from another source, and applying it, apprenticing with a tuner, etc. I read a post where the poster was learning by trial, and error, like stated above , kinda risky, I will run tried and true tunes from top tuners, but just want to tinker with a stock tune at some point in the future, when that time comes, I don't want to have to buy jet another piece of hardware, all I am asking is what is the best frame work of hardware, and software, to achieve my goals, and find out what, how, or if an emulator will benefit me, can the emulator be ran instead of a chip?
Like I said, if you plan on tinkering, or even looking at the tunes on the chips, it is going to require additional hardware and software to do it.
As I mentioned - the only ones (that I know of) that you might even be able to look into will the Ts Chips since I've seen their firmware burners on ebay.
TS Performance 7 3BS 7 3 Ford Powerstroke 4 Bank Chip Burner Software | eBay
Short of getting an EPROM programmer and doing it that way is really going to be your other option, let alone getting quarter horse/binary editor and other tools to dig into the PCM.
As for the tuners that have the flash tunes emailed - I do not know any tools to dig into those as those, as they are usually also proprietary, and the vendors that sell those usually have disclosure documents to not leak those out to the public.
Especially since this is income for them for their tunes, they're not going to want that out in the wild....
But here's a site where you can get most of the tools
http://www.moates.net/
EDIT:
Looks like they have some stuff for EFI Live - so there may be some other options for you.
Thread Starter
|
Junior User
Joined: Dec 2010
Posts: 95
Likes: 0
From: North Ga.
I hear ya and I applaud the person that is the DIY type.
Like I said, if you plan on tinkering, or even looking at the tunes on the chips, it is going to require additional hardware and software to do it.
As I mentioned - the only ones (that I know of) that you might even be able to look into will the Ts Chips since I've seen their firmware burners on ebay.
TS Performance 7 3BS 7 3 Ford Powerstroke 4 Bank Chip Burner Software | eBay
Short of getting an EPROM programmer and doing it that way is really going to be your other option, let alone getting quarter horse/binary editor and other tools to dig into the PCM.
As for the tuners that have the flash tunes emailed - I do not know any tools to dig into those as those, as they are usually also proprietary, and the vendors that sell those usually have disclosure documents to not leak those out to the public.
Especially since this is income for them for their tunes, they're not going to want that out in the wild....
But here's a site where you can get most of the tools
Welcome to www.moates.net! : Moates.Net
EDIT:
Looks like they have some stuff for EFI Live - so there may be some other options for you.
Like I said, if you plan on tinkering, or even looking at the tunes on the chips, it is going to require additional hardware and software to do it.
As I mentioned - the only ones (that I know of) that you might even be able to look into will the Ts Chips since I've seen their firmware burners on ebay.
TS Performance 7 3BS 7 3 Ford Powerstroke 4 Bank Chip Burner Software | eBay
Short of getting an EPROM programmer and doing it that way is really going to be your other option, let alone getting quarter horse/binary editor and other tools to dig into the PCM.
As for the tuners that have the flash tunes emailed - I do not know any tools to dig into those as those, as they are usually also proprietary, and the vendors that sell those usually have disclosure documents to not leak those out to the public.
Especially since this is income for them for their tunes, they're not going to want that out in the wild....
But here's a site where you can get most of the tools
Welcome to www.moates.net! : Moates.Net
EDIT:
Looks like they have some stuff for EFI Live - so there may be some other options for you.
Trending Topics
Elder User
Joined: Jan 2012
Posts: 695
Likes: 1
From: Littleton, CO
If I understand you correctly, if you have a design you're willing to "Open Source", might be worth while for you to look into covered under a GNU/GPL style or even "CopyLeft" (no that's not a misspell) license.
FTE Stories
Ford Trucks for Ford Truck Enthusiasts
10 Things Every Truck Owner NEEDS (2026 Edition)
Michael S. Palmer
Rezvani's Latest Post-Apocalyptic Monster Is a Ford F-150 Raptor Underneath
Verdad Gallardo
Top 10 Most Expensive Ford Trucks Ever Sold on Bring a Trailer
Joe Kucinski
2027 Ford Super Duty Buyer's Guide (Every Model, Engine, & Package)
Brett Foote
Top 10 Ford Truck Tragedies
Joe Kucinski
AEV FXL Super Duty - the Super Duty Raptor Ford Doesn't Make
Brett Foote
Lobo Vs Lobo: Proof the F-150 Lobo Should Be Even Lower!
Michael S. Palmer
Ford's 2001 Explorer Sportsman Concept Looks For a New Home
Verdad Gallardo
10 Best Ford Truck Engines We Miss the Most!
Joe Kucinski
Thread Starter
|
Junior User
Joined: Dec 2010
Posts: 95
Likes: 0
From: North Ga.
I design custom fiberglass automotive, and motorcycle parts, and this is a perfect example of what I am talking about, with the wicked wheel gen II, I have no connection to it, but Bob is going through what I have gone through, my stuff is easily copied, just like his, I feel for him, i am sure he did his copyright paperwork, but still a pita,
https://www.ford-trucks.com/forums/1...l#post12779944
https://www.ford-trucks.com/forums/1...l#post12779944
Elder User
Joined: Jan 2012
Posts: 695
Likes: 1
From: Littleton, CO
I think I understand you a little more clearly now, and absolutely agree.
And Bob is being a little vocal about it as well.
The actual thread in discussion about that is over here:
riffraff billet wheel? ?? - PowerStrokeArmy
Playing a little Devil's advocate - the billet wheels that's over at RiffRiff's has been up for a his site for sale for some time. (I know this because I've been looking at getting one for the longest time - before Bob's was introduced.)
However, I can't say it's a 'knock-off' as technically - it's not.
It's been manufactured by someone else - however, compared to other wheels for similar functionality...
I know it's just Symantec's and word play - but yes, could easily be misinterpreted.
But sure thing - I agree with you.
Copyright and patent design's are key for something like that.
And Bob is being a little vocal about it as well.
The actual thread in discussion about that is over here:
riffraff billet wheel? ?? - PowerStrokeArmy
Playing a little Devil's advocate - the billet wheels that's over at RiffRiff's has been up for a his site for sale for some time. (I know this because I've been looking at getting one for the longest time - before Bob's was introduced.)
However, I can't say it's a 'knock-off' as technically - it's not.
It's been manufactured by someone else - however, compared to other wheels for similar functionality...
I know it's just Symantec's and word play - but yes, could easily be misinterpreted.
But sure thing - I agree with you.
Copyright and patent design's are key for something like that.
Thread Starter
|
Junior User
Joined: Dec 2010
Posts: 95
Likes: 0
From: North Ga.
I kinda jumped the gun on that one, but it illustrates how important copyright patents are, IIRC there needs to be a 20% difference in design to not be called a copy, I don't mind if people gain inspiration from my designs, and improve on them, just change it more than 20%, don't just "splash" ( fiberglass industry term for using an existing part to make a mold off ) it.
Thread
Thread Starter
Forum
Replies
Last Post
hucka1a
1999 - 2003 7.3L Power Stroke Diesel
23
Jul 8, 2010 03:21 PM
