June B.S. Thread
FTE Chapter Leader
Joined: Mar 2005
Posts: 23,850
Likes: 9
From: Suppertown, MN
Yeah not as bad as I thought but they haven't gotten real deep yet so I am sure it will get worse!
VT Chapter Ldr
Joined: Apr 2004
Posts: 96,102
Likes: 294
From: Orange, Vermont
Good morning Dustin. Ok that's what I did. I read on on site it said to add oil to the filter housing after the filter was in. Wasn't sure. I don't think I'll go 5000 miles, oil seemed really black.
Also saw both rubber boots ripped
on the driver side axel shaft. Have you ever replaced those or know of a good write up on how to do it? 
Also saw both rubber boots ripped
on the driver side axel shaft. Have you ever replaced those or know of a good write up on how to do it? 
Fleet Owner
Joined: Mar 2003
Posts: 24,724
Likes: 74
From: Blue Hill Township
It looks like they are going to be putting that gravel crap down again soon...
FTE Chapter Leader
Joined: Mar 2005
Posts: 23,850
Likes: 9
From: Suppertown, MN
Ahhh sealcoating is always fun.
FTE Stories
Ford Trucks for Ford Truck Enthusiasts
2027 Ford Super Duty Buyer's Guide (Every Model, Engine, & Package)
Brett Foote
Top 10 Ford Truck Tragedies
Joe Kucinski
AEV FXL Super Duty - the Super Duty Raptor Ford Doesn't Make
Brett Foote
Lobo Vs Lobo: Proof the F-150 Lobo Should Be Even Lower!
Michael S. Palmer
Ford's 2001 Explorer Sportsman Concept Looks For a New Home
Verdad Gallardo
10 Best Ford Truck Engines We Miss the Most!
Joe Kucinski
2026 Shelby F-150 Off-Road: Better Than a Raptor R?
Brett Foote
2027 Super Duty Carhartt Package First Look: 12 Things You NEED to Know!
Michael S. Palmer
10 Most Surprising 2026 Ford Truck Features!
Joe Kucinski
Fleet Owner
Joined: Mar 2007
Posts: 28,289
Likes: 6
From: BLT, MN
I saw that huge pile at the city works place. The county threw some crappy patch and gravel down on 81 turning onto 30 that almost took me out yesterday.
Postmaster
Joined: Jun 2011
Posts: 3,293
Likes: 0
From: On the saddle
I didn't see it.. you snuck it in there on me.
I've done the axle shaft on MK3s, and on b5.5s... The key to both is having the triple squares. they've been using them since the early 80's.
ATD Tools 13782 10 pc. Triple Square Spline Bit Socket Set | SJDiscounttools.com.
I've done the axle shaft on MK3s, and on b5.5s... The key to both is having the triple squares. they've been using them since the early 80's.
ATD Tools 13782 10 pc. Triple Square Spline Bit Socket Set | SJDiscounttools.com.
Fleet Owner
Joined: Mar 2007
Posts: 28,289
Likes: 6
From: BLT, MN
I didn't see it.. you snuck it in there on me.
I've done the axle shaft on MK3s, and on b5.5s... The key to both is having the triple squares. they've been using them since the early 80's.
ATD Tools 13782 10 pc. Triple Square Spline Bit Socket Set | SJDiscounttools.com.
I've done the axle shaft on MK3s, and on b5.5s... The key to both is having the triple squares. they've been using them since the early 80's.
ATD Tools 13782 10 pc. Triple Square Spline Bit Socket Set | SJDiscounttools.com.
Fleet Owner
Joined: Mar 2003
Posts: 24,724
Likes: 74
From: Blue Hill Township
I will drive it there. I happened to have the car at home so I needed to figure out a way to get it on the flatbed anyway but I don't think that is going to happen.
Sealcoating isn't bad. The gravel sucks. Bad.
I bet Jay will enjoy it with the motorbike.
Posting Guru
Joined: Dec 2008
Posts: 1,764
Likes: 0
Have fun and kick their *****.It's a blast Jay. Take some bike classes out there if you haven't. Not only is it a blast to ride, but you might learn something too. And since they are instructional classes, you are covered by insurance as opposed to a race track, where you are not. I know this first hand. That's where my son crashed my 600RR. My son-->
<--me
FTE Chapter Leader
Joined: Mar 2005
Posts: 23,850
Likes: 9
From: Suppertown, MN
Yeah that would be a bugger to get on the trailer. Sounds like it should be good time! Good luck and have fun!