and will it go to 100psi?? 2-3 weeks in "Edge" time could be a few months... we'll see
Edge Insight New Update !!!!
Laughing Gas
Joined: Jan 2010
Posts: 854
Likes: 17
From: Florida
Dan, I think you are wrong, I got this email from Edge on Mar 10th :
Gerry,
We are in the final stages of testing for the pressure sensor. We hope to have these available to ship within the next month or so. You will receive an email when these become ready to ship.
Let me know if I can assist you with anything else.
Edge Products Technical Support
1080 S. Depot Drive
Ogden, UT 84404
Toll Free: 888-360-3343
Local: 801-476-3343
Tech Fax: 801-337-2198
Email: tech@edgeproducts.com
Edge Products| The Leaders in Performance Electronics
GR
Gerry,
We are in the final stages of testing for the pressure sensor. We hope to have these available to ship within the next month or so. You will receive an email when these become ready to ship.
Let me know if I can assist you with anything else.
Edge Products Technical Support
1080 S. Depot Drive
Ogden, UT 84404
Toll Free: 888-360-3343
Local: 801-476-3343
Tech Fax: 801-337-2198
Email: tech@edgeproducts.com
Edge Products| The Leaders in Performance Electronics
GR
Posting Guru
Joined: Oct 2006
Posts: 1,693
Likes: 7
From: Francestown, NH
http://edgeproducts.mv.treehousei.co...AS_Release.pdf
This was posted on powerstroke.org
Looks like a nice brochure on the whole expandable format. It says here their pressure sensor will only read up to 50psi (too low for our fuel) so maybe they're still working on it(?).
One nice comment on the page is they say sensors from manufacturers other than Edge can also be attached to a CS or CTS device through the EAS Universal Sensor Input. However, although that is very helpful, it's a little different from the answers they've been giving some of the posters here when they've emailed them a question.
I can't find this brochure or some of these items on their site so I'm not quite sure where this all stands.
This was posted on powerstroke.org
Looks like a nice brochure on the whole expandable format. It says here their pressure sensor will only read up to 50psi (too low for our fuel) so maybe they're still working on it(?).
One nice comment on the page is they say sensors from manufacturers other than Edge can also be attached to a CS or CTS device through the EAS Universal Sensor Input. However, although that is very helpful, it's a little different from the answers they've been giving some of the posters here when they've emailed them a question.
I can't find this brochure or some of these items on their site so I'm not quite sure where this all stands.
FTE Legend
Joined: Mar 2009
Posts: 161,105
Likes: 8,088
From: North Bay Ont Canada
This is the email I got yesterday when I asked when the fuel gauge would be ready,
whats not to understand:
Gerry,
I'm assuming you want to know if we can pull it from the factory computer? You will be able to install a pressure sensor with our 5V Universal option we are currently working on. I'm not sure I fully understand your question, however if you call one of my techs at the number below we will get you taken care of.
thanks,
Edge Products Technical Support
1080 S. Depot Drive
Ogden, UT 84404
Toll Free: 888-360-3343
Local: 801-476-3343
Tech Fax: 801-337-2198
Email: tech@edgeproducts.com
Edge Products| The Leaders in Performance Electronics
whats not to understand:
Gerry,
I'm assuming you want to know if we can pull it from the factory computer? You will be able to install a pressure sensor with our 5V Universal option we are currently working on. I'm not sure I fully understand your question, however if you call one of my techs at the number below we will get you taken care of.
thanks,
Edge Products Technical Support
1080 S. Depot Drive
Ogden, UT 84404
Toll Free: 888-360-3343
Local: 801-476-3343
Tech Fax: 801-337-2198
Email: tech@edgeproducts.com
Edge Products| The Leaders in Performance Electronics
Elder User
Joined: Aug 2010
Posts: 685
Likes: 0
From: Ft. Worth, TX
I downloaded the new software today and found 5 or 6 new PIDs to monitor. My only problem is that I don't know what all of them stand for, and what values I should be looking for. Anyone have a cheat sheet???
FTE Legend
Joined: Mar 2009
Posts: 161,105
Likes: 8,088
From: North Bay Ont Canada
On Mar 22nd I spoke to a tech & this is what he said:
they are working on a 5 volt pressure sensor, It will be ready in 2 or 3 wks, it comes with a cable, the cost will be around $150.00.................WOW, talk about run around.
they are working on a 5 volt pressure sensor, It will be ready in 2 or 3 wks, it comes with a cable, the cost will be around $150.00.................WOW, talk about run around.
FTE Legend
Joined: Mar 2009
Posts: 161,105
Likes: 8,088
From: North Bay Ont Canada
Ya, there must be an Edge time zone somewhere, Dan
They tell us what we want to hear............
They tell us what we want to hear............
FTE Stories
Ford Trucks for Ford Truck Enthusiasts
Rezvani's Latest Post-Apocalytic Monster Is a Ford F-150 Raptor Underneath
Verdad Gallardo
Top 10 Most Expensive Ford Trucks Ever Sold on Bring a Trailer
Joe Kucinski
2027 Ford Super Duty Buyer's Guide (Every Model, Engine, & Package)
Brett Foote
Top 10 Ford Truck Tragedies
Joe Kucinski
AEV FXL Super Duty - the Super Duty Raptor Ford Doesn't Make
Brett Foote
Lobo Vs Lobo: Proof the F-150 Lobo Should Be Even Lower!
Michael S. Palmer
Ford's 2001 Explorer Sportsman Concept Looks For a New Home
Verdad Gallardo
10 Best Ford Truck Engines We Miss the Most!
Joe Kucinski
2026 Shelby F-150 Off-Road: Better Than a Raptor R?
Brett Foote
Thread
Thread Starter
Forum
Replies
Last Post
