1972 Side mount tank replacement
#77
When it ended, went to Carpenters in Concord, bought a pile of NOS parts, also bought the hood letters for the Galaxie, but Carpenter was out of stock.
When they arrived several weeks later, I was disgusted to see that they were made in China. The quality was terrible, so I threw them away, had my original letters re-chromed.
#78
Here are the photos and it shows the hose I ordered for a 73 up which is the only one available, is merely an inch or two short! I think I will remove my metal filler neck pipe and use some exhaust tubing to section in a couple of inches to it. I don't know if it's visible but my Dennis Carpenter hose that costs 50.00 has a large " Made in China" stamped on it.
#80
Hi guys...I've enjoyed the conversations. I have a 68 F250 that I'm installing the drivers side saddle tank on. I bought the tank from LMC but can't come up with mounting straps. If I have to I could take something from a salvage and reform them, but I would rather use the right stuff. It looks like it had one in there before since I have the dash switch and the hole in the bed floor and the bed side have been welded up.I don't see where the straps would hook to the frame, but then I don't really know what I'm looking for...Any help would be appreciated. Thanks
#81
Hi guys...I've enjoyed the conversations. I have a 68 F250 that I'm installing the drivers side saddle tank on. I bought the tank from LMC but can't come up with mounting straps. If I have to I could take something from a salvage and reform them, but I would rather use the right stuff. It looks like it had one in there before since I have the dash switch and the hole in the bed floor and the bed side have been welded up.I don't see where the straps would hook to the frame, but then I don't really know what I'm looking for...Any help would be appreciated. Thanks
#82
Finally got my auxiliary fuel tank filler neck extended. After getting a quote from an exhaust shop of 30.00 just to make an adapter for me, I went to Auto Zone and paid 2.99 for a 2 1/8 inch exhaust coupler. I cut the filler neck and added in about 2 inches. problem solved. It's always one more thing with this project. Now all I have to do is order a rubber grommet for where the filler neck goes through the bed side.
#83
#84
Well I just went through this. PO had purchased a new tank. it is a spectra premium F25A
Link: ecat
They sell new for $130. Listed apps are for a dent. Only PN ref I found was D8TZ-9002-J
The vent tube is on the wrong side, but not a big issue to solve.
Sending unit is a D7TZ-9275-B from JBGY
1973-1979 Ford F Series Sending Unit, Side Mount-Broncograveyard.com
The tank straps were all bent and needed help so not sure how exactly close this should have fit. I did some hammering where the straps contact the tank, like the factory tank did and it fit but not perfectly. I replaced all rubber hoses with decent fuel rated hose from here:
Filler Neck Supply: Gas Filler Hose | Fuel Filler Necks
Overall these parts work, truck is back on the road.
Link: ecat
They sell new for $130. Listed apps are for a dent. Only PN ref I found was D8TZ-9002-J
The vent tube is on the wrong side, but not a big issue to solve.
Sending unit is a D7TZ-9275-B from JBGY
1973-1979 Ford F Series Sending Unit, Side Mount-Broncograveyard.com
The tank straps were all bent and needed help so not sure how exactly close this should have fit. I did some hammering where the straps contact the tank, like the factory tank did and it fit but not perfectly. I replaced all rubber hoses with decent fuel rated hose from here:
Filler Neck Supply: Gas Filler Hose | Fuel Filler Necks
Overall these parts work, truck is back on the road.
#87
Front: 1968/69 F100/250 Flareside/Styleside 115/131" wheelbases & F350 Styleside 135" wheelbase.
Rear: 1968/72 F100/250 Flareside/Styleside 131" wheelbase & F350 Styleside 135" wheelbase.
No Ford dealer or obsolete parts vendor has any.
#89
#90
Well I just went through this. PO had purchased a new tank. it is a spectra premium F25A
Link: ecat
They sell new for $130. Listed apps are for a dent. Only PN ref I found was D8TZ-9002-J
The vent tube is on the wrong side, but not a big issue to solve.
Sending unit is a D7TZ-9275-B from JBGY
1973-1979 Ford F Series Sending Unit, Side Mount-Broncograveyard.com
The tank straps were all bent and needed help so not sure how exactly close this should have fit. I did some hammering where the straps contact the tank, like the factory tank did and it fit but not perfectly. I replaced all rubber hoses with decent fuel rated hose from here:
Filler Neck Supply: Gas Filler Hose | Fuel Filler Necks
Overall these parts work, truck is back on the road.
Link: ecat
They sell new for $130. Listed apps are for a dent. Only PN ref I found was D8TZ-9002-J
The vent tube is on the wrong side, but not a big issue to solve.
Sending unit is a D7TZ-9275-B from JBGY
1973-1979 Ford F Series Sending Unit, Side Mount-Broncograveyard.com
The tank straps were all bent and needed help so not sure how exactly close this should have fit. I did some hammering where the straps contact the tank, like the factory tank did and it fit but not perfectly. I replaced all rubber hoses with decent fuel rated hose from here:
Filler Neck Supply: Gas Filler Hose | Fuel Filler Necks
Overall these parts work, truck is back on the road.