wheel question
Thread Starter
|
Senior User
Joined: Oct 2007
Posts: 180
Likes: 2
Originally Posted by KingRanchMan02
Did you ever take the time to check the backspacing on your stock wheels? How does it compare to these wheels? 
Posting Guru
Joined: Oct 2005
Posts: 2,209
Likes: 1
From: Louisville, Kentucky
Take a wheel off of the truck and lay it face down on the ground. Get a straight edge and lay it across the wheel lip where the tire bead seals. Then measure from the wheel flange (that sits against the wheel hub) up to the straight edge. This measurement is the wheel offset or backspacing.
Hotshot
Joined: Jun 2003
Posts: 12,341
Likes: 4,366
From: SW VA
https://www.rsracing.com/tech-wheel.html
Stock backspacing is 4.5" if I recall. Basically, your wheels will be recessed into the fenderwell 1/2" on each side.
Stock backspacing is 4.5" if I recall. Basically, your wheels will be recessed into the fenderwell 1/2" on each side.
Thread Starter
|
Senior User
Joined: Oct 2007
Posts: 180
Likes: 2
Originally Posted by ATC Crazy
https://www.rsracing.com/tech-wheel.html
Stock backspacing is 4.5" if I recall. Basically, your wheels will be recessed into the fenderwell 1/2" on each side.
Stock backspacing is 4.5" if I recall. Basically, your wheels will be recessed into the fenderwell 1/2" on each side.
Tuned
Joined: Dec 1999
Posts: 464
Likes: 1
From: Bismarck USA
Basically he's saying your rims would be 1/2 inch closer to your engine, assuming 5 inch BS wheels and stock is 4.5 inches.
If those assumptions are correct (I don't know the stock spacing myself either), the issue to look for would be the wheel either rubbing some suspension member or possible the fender well when you fully turn the wheels to one side or the other.
If those assumptions are correct (I don't know the stock spacing myself either), the issue to look for would be the wheel either rubbing some suspension member or possible the fender well when you fully turn the wheels to one side or the other.
Trending Topics
Thread Starter
|
Senior User
Joined: Oct 2007
Posts: 180
Likes: 2
Originally Posted by 92merc
Basically he's saying your rims would be 1/2 inch closer to your engine, assuming 5 inch BS wheels and stock is 4.5 inches.
If those assumptions are correct (I don't know the stock spacing myself either), the issue to look for would be the wheel either rubbing some suspension member or possible the fender well when you fully turn the wheels to one side or the other.
If those assumptions are correct (I don't know the stock spacing myself either), the issue to look for would be the wheel either rubbing some suspension member or possible the fender well when you fully turn the wheels to one side or the other.
http://www.jegs.com/webapp/wcs/store...10002_99360_-1
Soft 8 397 Series Wheel
Size: 16'' x 8''
Bolt Circle: 5 x 135mm
Rear Spacing: 5''
FTE Stories
Ford Trucks for Ford Truck Enthusiasts
Rezvani's Latest Post-Apocalytic Monster Is a Ford F-150 Raptor Underneath
Verdad Gallardo
Top 10 Most Expensive Ford Trucks Ever Sold on Bring a Trailer
Joe Kucinski
2027 Ford Super Duty Buyer's Guide (Every Model, Engine, & Package)
Brett Foote
Top 10 Ford Truck Tragedies
Joe Kucinski
AEV FXL Super Duty - the Super Duty Raptor Ford Doesn't Make
Brett Foote
Lobo Vs Lobo: Proof the F-150 Lobo Should Be Even Lower!
Michael S. Palmer
Ford's 2001 Explorer Sportsman Concept Looks For a New Home
Verdad Gallardo
10 Best Ford Truck Engines We Miss the Most!
Joe Kucinski
