help!
Thread Starter
|
Freshman User
Joined: Jun 2003
Posts: 35
Likes: 0
From: channelview tx
help!
just drove 50 f1 to the store wow almost didnt make it back sputtering
jerking i think wire from gen to wiring harness i am going to try
to trace it now it done it a while back and thats what it was i hope
any other suggestions ?? thanks richard jobe
jerking i think wire from gen to wiring harness i am going to try
to trace it now it done it a while back and thats what it was i hope
any other suggestions ?? thanks richard jobe
Postmaster
Joined: Mar 2000
Posts: 3,730
Likes: 13
From: Waynesville, OH
Richard - as always, in the absence of a obvious problem, eliminate one thing at a time until you find the problem. Sounds like some sort of ignition problem, but might be a fuel problem. Kinda doubt it's your generator - but it's possible.
Replace your points, condenser, rotor, and distributor cap. Cheap stuff that may eliminate the problem. Check the low-voltage wire (not the spark wire) from the coil to the distributor. Make sure to check the connection of this wire inside the distributor. Also check the braided wire inside the distributor to make sure it isn't frayed, broken, or shorting out. If all that fails to fix the problem, you might try a new coil and/or ballast resistor (if your truck has one). Finally, make sure you have a good, solid system voltage supply at the input to your ignition system (ballast resistor or coil if you don't have a ballast resistor). Then move on to the fuel system. Good luck.
Replace your points, condenser, rotor, and distributor cap. Cheap stuff that may eliminate the problem. Check the low-voltage wire (not the spark wire) from the coil to the distributor. Make sure to check the connection of this wire inside the distributor. Also check the braided wire inside the distributor to make sure it isn't frayed, broken, or shorting out. If all that fails to fix the problem, you might try a new coil and/or ballast resistor (if your truck has one). Finally, make sure you have a good, solid system voltage supply at the input to your ignition system (ballast resistor or coil if you don't have a ballast resistor). Then move on to the fuel system. Good luck.
Thread Starter
|
Freshman User
Joined: Jun 2003
Posts: 35
Likes: 0
From: channelview tx
thanks
you were right it wasnt gen wire i messed up it was the wire from coil goes right next to gen wire it was briken and grounding out thanks we are back
running again i am looking to put a girley 302 & trans i already have r end
out early 90s f150 thanks richard jobe houston texas life&limb houston freeways
running again i am looking to put a girley 302 & trans i already have r end
out early 90s f150 thanks richard jobe houston texas life&limb houston freeways
Cargo Master
Joined: Nov 2004
Posts: 2,858
Likes: 3
From: Friendswood, Texas
Richard,
Do you have a flathead in there now? If you do and you are going to replace it, please let me know. I would be interested in it. I have a couple of engine-less trucks at the moment that I would like to put flatheads back in. And I'm just up the road from you. Would love to see your truck sometime. Please post some pictures.
Do you have a flathead in there now? If you do and you are going to replace it, please let me know. I would be interested in it. I have a couple of engine-less trucks at the moment that I would like to put flatheads back in. And I'm just up the road from you. Would love to see your truck sometime. Please post some pictures.
Hotshot
Joined: Oct 2004
Posts: 15,882
Likes: 88
From: Durham NC
Richard, Just a friendly suggestion:
If you start you sentences with a capital letter and end them with a period it would go a long way towards making it easier to read and understand your posts. Or at least hit an enter after each so they start on a new line. There are many of us OF's here that have a problem translating IM or email dialect (or whatever it is) that might be able to give assistance if we could understand what is being asked.
If you start you sentences with a capital letter and end them with a period it would go a long way towards making it easier to read and understand your posts. Or at least hit an enter after each so they start on a new line. There are many of us OF's here that have a problem translating IM or email dialect (or whatever it is) that might be able to give assistance if we could understand what is being asked.
Cargo Master
Joined: Nov 2004
Posts: 2,858
Likes: 3
From: Friendswood, Texas
AX,
It's the Channelview in him. Remember the Texas Cheerleader mom story? That was C-view. (Richard - Hope you know I'm just busting your chops a little. Glad to see another Houstonian on here. Hope you stick around - and let me know about that Flathead if that's what's still in there.)
It's the Channelview in him. Remember the Texas Cheerleader mom story? That was C-view. (Richard - Hope you know I'm just busting your chops a little. Glad to see another Houstonian on here. Hope you stick around - and let me know about that Flathead if that's what's still in there.)
Tuned
Joined: Oct 2000
Posts: 262
Likes: 4
From: Lake Jackson, Texas
Trending Topics
Cargo Master
Joined: Nov 2004
Posts: 2,858
Likes: 3
From: Friendswood, Texas
FTE Stories
Ford Trucks for Ford Truck Enthusiasts
2027 Ford Super Duty Buyer's Guide (Every Model, Engine, & Package)
Brett Foote
Top 10 Ford Truck Tragedies
Joe Kucinski
AEV FXL Super Duty - the Super Duty Raptor Ford Doesn't Make
Brett Foote
Lobo Vs Lobo: Proof the F-150 Lobo Should Be Even Lower!
Michael S. Palmer
Ford's 2001 Explorer Sportsman Concept Looks For a New Home
Verdad Gallardo
10 Best Ford Truck Engines We Miss the Most!
Joe Kucinski
2026 Shelby F-150 Off-Road: Better Than a Raptor R?
Brett Foote
2027 Super Duty Carhartt Package First Look: 12 Things You NEED to Know!
Michael S. Palmer
