Pyrometer problems
Thread Starter
|
New User
Joined: Sep 2004
Posts: 4
Likes: 0
Pyrometer problems
I just installed an Autometer Pro-Comp pyrometer to replace a VDO unit that I decided was too slow in responding. My problem is that the Autometer unit resembles the second hand of a watch ...... the needle jumps between readings in increments of about 25-50 degrees. This happens going up as well as down in temperature. This is kind of frustrating and I was hoping that someone else had expreienced this and can offer a remedy. My VDO unit though slow was very smooth in its operation and I am wondering why I replaced it.
Any advice is appreciated.
Any advice is appreciated.
Fleet Mechanic
Joined: Oct 2003
Posts: 1,764
Likes: 0
From: CentralEastern Utah
I was about to post on this topic. I really like my VDO pyro. Steady and smooth. I really don't think its slow though.... I did'nt know any different untill I installed a autometer pyro in my brothers cummins. Its all over the place. Re-acts right with the throttle. Is this normal???
Fleet Mechanic
Joined: Oct 2003
Posts: 1,764
Likes: 0
From: CentralEastern Utah
Originally Posted by cookie88
Did you alter the length of the thermocouple leads? Or, does one or the other gauge require an external amplifier?
FTE Leadership Emeritus
Joined: May 2001
Posts: 13,653
Likes: 6
From: Cabot, Arkansas
Originally Posted by ltfox
I was wondering, I was always told not to use any connector on the thermocouple leads that weren't supplied. Screws up the resistance thing in the pyro.... My brother insisted on using regular crimp eye connectors to connect to the back of his pyro. Will this screw with the readings???
Postmaster
Joined: Dec 2003
Posts: 2,864
Likes: 0
From: STEPHENVILLE,TX!!!!!
yeah it will the gauges are calibrated to a certain resistance rating. the supplied wire and connectors are a certain metal with certain resistance qualities. a bad voltage source will make your gauge go all over the place also. i like the autometers cause there the fastest responding gauges on the market.
Trending Topics
Thread Starter
|
New User
Joined: Sep 2004
Posts: 4
Likes: 0
Thanks for the reply's. Cookie, I used the wire and connectors just as supplied by Autometer. I did not alter anything. seems to me like there is a problem with the gauge movement itself. I will attempt to contact Autometer and see what they say.
FTE Stories
Ford Trucks for Ford Truck Enthusiasts
Top 10 Most Expensive Ford Trucks Ever Sold on Bring a Trailer
Joe Kucinski
2027 Ford Super Duty Buyer's Guide (Every Model, Engine, & Package)
Brett Foote
Top 10 Ford Truck Tragedies
Joe Kucinski
AEV FXL Super Duty - the Super Duty Raptor Ford Doesn't Make
Brett Foote
Lobo Vs Lobo: Proof the F-150 Lobo Should Be Even Lower!
Michael S. Palmer
Ford's 2001 Explorer Sportsman Concept Looks For a New Home
Verdad Gallardo
10 Best Ford Truck Engines We Miss the Most!
Joe Kucinski
2026 Shelby F-150 Off-Road: Better Than a Raptor R?
Brett Foote
2027 Super Duty Carhartt Package First Look: 12 Things You NEED to Know!
Michael S. Palmer
Laughing Gas
Joined: Jul 2003
Posts: 1,157
Likes: 1
From: Littleton, Colorado
I'm probably a little late on this post, but I would check with autometer. I've got the Autometer sportcomp pyro, and its smooth as silk. I would check your ground first, and if all is well you might have got ahold of a bad thermocoupler.
Hope you get it handled
Austin
Hope you get it handled
Austin
FTE Leadership Emeritus
Joined: May 2001
Posts: 13,653
Likes: 6
From: Cabot, Arkansas
Originally Posted by Jackcd
Thanks for the reply's. Cookie, I used the wire and connectors just as supplied by Autometer. I did not alter anything. seems to me like there is a problem with the gauge movement itself. I will attempt to contact Autometer and see what they say.
Thread
Thread Starter
Forum
Replies
Last Post
oldblue89
Pre-Power Stroke Diesel (7.3L IDI & 6.9L)
7
May 22, 2012 11:41 AM
stangclassic66
1999 - 2003 7.3L Power Stroke Diesel
8
Feb 22, 2011 07:06 AM
