Still having issues.
Thread Starter
|
Senior User
Joined: Oct 2011
Posts: 247
Likes: 0
From: Poteau,Oklahoma
Still having issues.
Ok so truck was smoking a ton and then shut off, replaced the IPR with a new one, still getting a ton of smoke so took out all of the injectors found one with a broken tip and ordered a new one, ordered new o-rings for all of them and installed them.
Just got everything put back together tonight, took it for a spin, about 20 miles, I get white smoke when keeping it at a steady speed and grey/black smoke when I stomp on it.
Still seems to be running a little rough still.
And it is shifting hard again, letting the engine rev. up to about 2700rpm before it shifts.
Noticed CCV Doghouse was leaking so I ordered new o-rings for that.
This truck is starting to drive me crazy, I feel like I am still missing something.
Has had a new ICP, & CPS within the last 2 months as well.
Also "wait to start" light isnt staying on very long since I have put all this back together, did I forget to plug something in? I tried to follow the directions provided from Riff Raff to a T.
Leaking some oil when I pulled back in, but pretty sure its from the CCV, and the oil level is good, I checked it.
What else should I check?
Just got everything put back together tonight, took it for a spin, about 20 miles, I get white smoke when keeping it at a steady speed and grey/black smoke when I stomp on it.
Still seems to be running a little rough still.
And it is shifting hard again, letting the engine rev. up to about 2700rpm before it shifts.
Noticed CCV Doghouse was leaking so I ordered new o-rings for that.
This truck is starting to drive me crazy, I feel like I am still missing something.
Has had a new ICP, & CPS within the last 2 months as well.
Also "wait to start" light isnt staying on very long since I have put all this back together, did I forget to plug something in? I tried to follow the directions provided from Riff Raff to a T.
Leaking some oil when I pulled back in, but pretty sure its from the CCV, and the oil level is good, I checked it.
What else should I check?
Last edited by 4x4countryboy; May 3, 2012 at 08:20 PM. Reason: more info.
Post Fiend
Joined: May 2009
Posts: 5,470
Likes: 3
From: Pea Ridge, AR
Ok so truck was smoking a ton and then shut off, replaced the IPR with a new one, still getting a ton of smoke so took out all of the injectors found one with a broken tip and ordered a new one, ordered new o-rings for all of them and installed them.
Just got everything put back together tonight, took it for a spin, about 20 miles, I get white smoke when keeping it at a steady speed and grey/black smoke when I stomp on it.
Still seems to be running a little rough still.
And it is shifting hard again, letting the engine rev. up to about 2700rpm before it shifts.
Noticed CCV Doghouse was leaking so I ordered new o-rings for that.
This truck is starting to drive me crazy, I feel like I am still missing something.
Has had a new ICP, & CPS within the last 2 months as well.
Also "wait to start" light isnt staying on very long since I have put all this back together, did I forget to plug something in? I tried to follow the directions provided from Riff Raff to a T.
Leaking some oil when I pulled back in, but pretty sure its from the CCV, and the oil level is good, I checked it.
What else should I check?
Just got everything put back together tonight, took it for a spin, about 20 miles, I get white smoke when keeping it at a steady speed and grey/black smoke when I stomp on it.
Still seems to be running a little rough still.
And it is shifting hard again, letting the engine rev. up to about 2700rpm before it shifts.
Noticed CCV Doghouse was leaking so I ordered new o-rings for that.
This truck is starting to drive me crazy, I feel like I am still missing something.
Has had a new ICP, & CPS within the last 2 months as well.
Also "wait to start" light isnt staying on very long since I have put all this back together, did I forget to plug something in? I tried to follow the directions provided from Riff Raff to a T.
Leaking some oil when I pulled back in, but pretty sure its from the CCV, and the oil level is good, I checked it.
What else should I check?
Just 20 miles since reinstalling the injectors? Wait a bit and see if it gets better, it can take quite a while. What about a quick check for blowby? Have you done that in a while?
Post Fiend
Joined: May 2009
Posts: 5,470
Likes: 3
From: Pea Ridge, AR
Quick check is with the motor running, flip the oi fill cap over and set it atop the oil fill neck, it should sit there with no pressure behind it.
A/Ox4 has a video in which he used a golf ball though too.
<iframe width="420" height="315" src="http://www.youtube.com/embed/fgwa3lf1d68" frameborder="0" allowfullscreen></iframe>
A/Ox4 has a video in which he used a golf ball though too.
Thread Starter
|
Senior User
Joined: Oct 2011
Posts: 247
Likes: 0
From: Poteau,Oklahoma
Checked it 2 weeks ago tops and it had none......but it sure does now! 
Now wherre do I go with this?
Now wherre do I go with this?
Last edited by 4x4countryboy; May 3, 2012 at 09:26 PM. Reason: added info
Post Fiend
Joined: May 2009
Posts: 5,470
Likes: 3
From: Pea Ridge, AR
Trending Topics
Post Fiend
Joined: May 2009
Posts: 5,470
Likes: 3
From: Pea Ridge, AR
Well before I jump to far ahead, you did just pull all injectors, what are the odds, you didn't get them seated greatly?
FTE Stories
Ford Trucks for Ford Truck Enthusiasts
10 Ugly Ford Trucks That We Still Kinda Love
Joe Kucinski
10 Things Every Truck Owner NEEDS (2026 Edition)
Michael S. Palmer
Rezvani's Latest Post-Apocalyptic Monster Is a Ford F-150 Raptor Underneath
Verdad Gallardo
Top 10 Most Expensive Ford Trucks Ever Sold on Bring a Trailer
Joe Kucinski
2027 Ford Super Duty Buyer's Guide (Every Model, Engine, & Package)
Brett Foote
Top 10 Ford Truck Tragedies
Joe Kucinski
AEV FXL Super Duty - the Super Duty Raptor Ford Doesn't Make
Brett Foote
Lobo Vs Lobo: Proof the F-150 Lobo Should Be Even Lower!
Michael S. Palmer
Ford's 2001 Explorer Sportsman Concept Looks For a New Home
Verdad Gallardo
Thread Starter
|
Senior User
Joined: Oct 2011
Posts: 247
Likes: 0
From: Poteau,Oklahoma
Its possible that I didnt, would kinda make sense wouldnt it? Golly I would hate to do all this all over again.
Any tricks for the back passenger side one? It was a pain! That would be my 1st guess for one that didnt get seated properly.
Any tricks for the back passenger side one? It was a pain! That would be my 1st guess for one that didnt get seated properly.
Post Fiend
Joined: May 2009
Posts: 5,470
Likes: 3
From: Pea Ridge, AR
Take off the VC's and use a straight edge across the solenoids to see if they are all seated well, also inspect all the pushrods and rocker arms for breaks or bends. Make sure you reinstalled the GP's and are not experiencing a leak there too.
Lead Driver
Joined: Sep 2005
Posts: 9,399
Likes: 188
From: Norco,CA
Alan is leading you the right way. But I think you need to do the compression test. Start with the one that had the broken tip. Pressure is always a bad sign sorry to say. I hope I'm wrong, good luck. I'll be watching this tread.
Chet
Chet
Thread
Thread Starter
Forum
Replies
Last Post
PSU4ME
1994.5 - 1997 7.3L Power Stroke Diesel
4
Jul 17, 2019 10:44 AM
85Supclub
1994.5 - 1997 7.3L Power Stroke Diesel
43
May 28, 2015 04:49 PM
frdf250
1999 - 2003 7.3L Power Stroke Diesel
18
Dec 23, 2014 11:22 AM
largefries
1999 - 2003 7.3L Power Stroke Diesel
7
Sep 17, 2012 09:50 PM
