Ford Truck Enthusiasts Forums
matted up to a Viper T-56 with ford input shaft and redone tail shaft to accept my cable speedo
matted up to a Viper T-56 with ford input shaft and redone tail shaft to accept my cable speedo
2 2016/02/12 17:04:17
welded 2 lightning intakes . All injector, COP holes match perfectly. and then welded adaptor plate
welded 2 lightning intakes . All injector, COP holes match perfectly. and then welded adaptor plate
1 2016/02/12 16:57:35
WS6 Wilwood 6-piston caliper. for front. Lot of weight up front
WS6 Wilwood 6-piston caliper. for front. Lot of weight up front
0 2016/02/14 17:49:09
this is the inside of the gas tank i build. Have to have baffles to help keep fuel in center where pickup is
this is the inside of the gas tank i build. Have to have baffles to help keep fuel in center where pickup is
0 2016/02/13 10:58:41
0 2016/02/12 19:14:45
moving COP to back of motor. I want top of motor free of wires . only wires will be for injectors
moving COP to back of motor. I want top of motor free of wires . only wires will be for injectors
0 2016/02/12 17:05:55
modifyed stock oil pan . it was the lowest part of truck . cant hve that
modifyed stock oil pan . it was the lowest part of truck . cant hve that
0 2016/02/12 17:03:08
shorten it . but still have full movement of float
shorten it . but still have full movement of float
0 2016/02/12 17:01:57
made gas tank. 15gal
made gas tank. 15gal
0 2016/02/12 17:01:05
manely Rods & pistons vs Stock ones
manely Rods & pistons vs Stock ones
0 2016/02/12 16:59:55
new valve covers
new valve covers
0 2016/02/12 16:58:46
ford v10. I made the valve covers but i changed them later
ford v10. I made the valve covers but i changed them later
0 2016/02/12 16:56:20
custom motor mount. Yes corvette mounts. sorry
custom motor mount. Yes corvette mounts. sorry
0 2016/02/12 16:55:08
passenger header since motor is so big plus i had to made room for the starter
passenger header since motor is so big plus i had to made room for the starter
0 2016/02/12 16:54:15
chromoly bump stops
chromoly bump stops
0 2016/02/12 16:53:46
made my own fuel rails. I wanted them to look the same length if you look at the front of the motor
made my own fuel rails. I wanted them to look the same length if you look at the front of the motor
0 2016/02/12 16:52:31
driver side
driver side
0 2016/02/12 15:49:34
header moke up for 1-5/8 PVC
header moke up for 1-5/8 PVC
0 2016/02/12 15:48:21
here they are and i made Bump stops too
here they are and i made Bump stops too
0 2016/02/12 15:47:27
the control arm i made in Chromoly. 2" long to bring the wheels out more
the control arm i made in Chromoly. 2" long to bring the wheels out more
0 2016/02/12 15:46:20
Tilton pedal aseemby i modified to add a gas pedal
Tilton pedal aseemby i modified to add a gas pedal
0 2016/02/12 15:24:24
0 2016/02/12 15:20:59
3/4 hiem joints . Cant go cheap on those
3/4 hiem joints . Cant go cheap on those
0 2016/02/12 15:18:55
0 2016/02/12 15:18:20
0 2016/02/10 15:57:24
made a custom Currie 9" with Moser center section with 31 spline axles
made a custom Currie 9" with Moser center section with 31 spline axles
0 2016/02/10 15:56:18
Shelby 18 x9 275/35/18 all around. add spacers to pull to corners wilwood 6-piston 14" rotors
Shelby 18 x9 275/35/18 all around. add spacers to pull to corners wilwood 6-piston 14" rotors
0 2016/02/10 15:53:44
Shelby 18" x 9" wheel 275/35/18 all around. Add spacers to make work. Wilwood 6-piston calipers & 14" rotor
Shelby 18" x 9" wheel 275/35/18 all around. Add spacers to make work. Wilwood 6-piston calipers & 14" rotor
0 2016/02/10 15:52:24
filling it to install door lock post
filling it to install door lock post
0 2016/02/10 15:51:11
filling in brake booster, install Tilton pedals with remote reservoirs
filling in brake booster, install Tilton pedals with remote reservoirs
0 2016/02/10 15:49:01
cut bed out to make wood bed
cut bed out to make wood bed
0 2016/02/10 15:47:55
on a Fatman Frame
on a Fatman Frame
0 2016/02/10 15:46:22
what it looked like before cutting & welding folded sheetmetal
what it looked like before cutting & welding folded sheetmetal
0 2016/02/10 15:44:57
cut & welded folded sheet metal on body to give clean look
cut & welded folded sheet metal on body to give clean look
0 2016/02/10 15:43:48
0 2016/02/10 15:41:26
0 2016/02/10 11:58:02
start to remove drip lip. never liked it
start to remove drip lip. never liked it
0 2016/02/10 11:53:49
0 2016/02/10 11:51:21
passenger header
passenger header
0 2012/08/04 14:53:30
driver side
driver side
0 2012/08/04 14:53:30