Ford Truck Enthusiasts Forums
Share Your Pictures with Our Community. Upload Now
Pieces I cut off using the PVC cutter shown.
Pieces I cut off using the PVC cutter shown.
0 2009/01/21 16:32:13
Ta-Da! Should help even when filling up the Aux Tank. BTW, thats 95 gals plus 38gals factory. Lucky it last me a month.
Ta-Da! Should help even when filling up the Aux Tank. BTW, thats 95 gals plus 38gals factory. Lucky it last me a month.
0 2009/01/21 16:32:13
Pedal assembly and master cylinder
Pedal assembly and master cylinder
0 2009/01/21 16:31:40
Master cylinder above crossmember
Master cylinder above crossmember
0 2009/01/21 16:31:40
More small crap. Front end.
More small crap. Front end.
0 2009/01/21 16:27:32
crap in the bottom of the tank. See the aluminum or steel, it appears the boys that installed the tank didn't even take the time to cover the factory fuel filler line connection on the factory tank when they were cutting the holes in the bed. Either that or the tank was not flushed from the factory. Its been in there since 2005.
crap in the bottom of the tank. See the aluminum or steel, it appears the boys that installed the tank didn't even take the time to cover the factory fuel filler line connection on the factory tank when they were cutting the holes in the bed. Either that or the tank was not flushed from the factory. Its been in there since 2005.
0 2009/01/21 16:27:32
Same. Rear end. No gel!
Same. Rear end. No gel!
0 2009/01/21 16:27:32
Stock steering box
Stock steering box
0 2009/01/21 16:25:44
Crossmember has been welded to frame. Chevrolet crossmember?
Crossmember has been welded to frame. Chevrolet crossmember?
0 2009/01/21 16:25:44
Master cylinder is bolted to frame. I was told that it might be attached to the tranny crossmember.
Master cylinder is bolted to frame. I was told that it might be attached to the tranny crossmember.
0 2009/01/21 16:25:44
Front crossmember is holding only the radiator.
Front crossmember is holding only the radiator.
0 2009/01/21 16:21:20
Frontend assembly to be replaced when changing to Toyota 4 X4 power steering.
Frontend assembly to be replaced when changing to Toyota 4 X4 power steering.
0 2009/01/21 16:21:20
Advertisement
Pitman assembly
Pitman assembly
0 2009/01/21 16:21:20
Another shot if the tank and straps.
Another shot if the tank and straps.
0 2009/01/21 16:20:04
Tank is out and on the floor.
Tank is out and on the floor.
0 2009/01/21 16:20:04
Passenger door gap larger at top of door than bottom
Passenger door gap larger at top of door than bottom
0 2009/01/21 16:16:19
283 C#@^y. Booooooooooooo!!!!!!
283 C#@^y. Booooooooooooo!!!!!!
0 2009/01/21 16:16:19
Entire fuse panel consists of 4 fuses
Entire fuse panel consists of 4 fuses
0 2009/01/21 16:16:19
Back side of the tank with strap.
Back side of the tank with strap.
0 2009/01/21 16:15:26
Looking up at the frame on the inside near the middle of the tank. It is the sending unit electrical connection, shown disconnected.
Looking up at the frame on the inside near the middle of the tank. It is the sending unit electrical connection, shown disconnected.
0 2009/01/21 16:15:26
Top of the tank with factory fuel pump and return lines still coneected. Remember my aux tank drains into my factory tank so no filler tube to remove. The sending unit electrical connection hanging.
Top of the tank with factory fuel pump and return lines still coneected. Remember my aux tank drains into my factory tank so no filler tube to remove. The sending unit electrical connection hanging.
0 2009/01/21 16:15:26
Last of the nasty fuel, nothing but air.
Last of the nasty fuel, nothing but air.
0 2009/01/21 16:10:23
Tank straps removed
Tank straps removed
0 2009/01/21 16:10:23
I used rachet straps to hold the tank and then lowered as needed with the clips by myself. Made it easy to stop and removed the connections when required. Stands were there as a back up. Kept the straps on the end as not to support the tank in the center where the level float is.
I used rachet straps to hold the tank and then lowered as needed with the clips by myself. Made it easy to stop and removed the connections when required. Stands were there as a back up. Kept the straps on the end as not to support the tank in the center where the level float is.
0 2009/01/21 16:10:23
BIG gap between hood and cowl
BIG gap between hood and cowl
0 2009/01/21 16:06:55
Hood and left fender missaligned
Hood and left fender missaligned
0 2009/01/21 16:06:55
Left fender and hood alignment. Gap too large at cowl and scratching paint by being too close at the fender.
Left fender and hood alignment. Gap too large at cowl and scratching paint by being too close at the fender.
0 2009/01/21 16:06:55
Used old fuel pump to drain tank, connected to factory suction.
Used old fuel pump to drain tank, connected to factory suction.
0 2009/01/21 16:05:14
Used a a switch to cut off and on between portable tanks.
Used a a switch to cut off and on between portable tanks.
0 2009/01/21 16:05:14
Just clipped it to the battery. BTW, pumped over 20 gals fuel and it pretty much drained my one battery (although my truck has been sitting for quite awhile waiting to be fixed).
Just clipped it to the battery. BTW, pumped over 20 gals fuel and it pretty much drained my one battery (although my truck has been sitting for quite awhile waiting to be fixed).
0 2009/01/21 16:05:14
Tank fill (locking cap for me) the next connection is the factory tank vent and the 3rd is the Aux tank vent.
Tank fill (locking cap for me) the next connection is the factory tank vent and the 3rd is the Aux tank vent.
0 2009/01/21 15:58:40
Drain to factory tank (size 38 Hanes, btw)
Drain to factory tank (size 38 Hanes, btw)
0 2009/01/21 15:58:40
Advertisement