Please help!!!
Thread Starter
|
Senior User
Joined: Apr 2009
Posts: 301
Likes: 0
From: Scenery hill,Pa.
Please help!!!
I keep having alot of issue with my door latches. I just replaced both switches and both latches. They same problem still exists being that the door switches work in reverse of how they should. When the doors are open the lights go out. Its suppsoed to work how any door switch works. When you open the door the switch opens and connects the circuit. Its working oppsite. With 2 new door latches its still got the same promblem. I ahev no idea whats wrong. Does someone out there have any advice. My truck is a 2002 f350 crew short bed lariet with 7.3.
Thread Starter
|
Senior User
Joined: Apr 2009
Posts: 301
Likes: 0
From: Scenery hill,Pa.
Well then why is it when i take the switch out and use it manualy it works the way it should. If it is the GEM where is it behind the fuse box? Is it kinda like a dumbed down body controler? Im used to body controler issues since i do alot of ESC work on international trucks. Im new to chassis work on superdutys so i dont know my way around yet. Do you know of any ways to check this? Any hints to give?
Junior User
Joined: Oct 2008
Posts: 51
Likes: 0
I had issues with my interior lights not working, the auto headlights not working and the radio not turning off when I removed the ignition keys.
The issue was a busted/fried VSM (Vehicle Security Module) Since your truck is a '02 it should have a VSM (not a GSM - from earlier trucks...) located behind the radio, mounted on the inside of the firewall - a small black box with three plugs - took me about an hour to get access to it. Don't know if there is a procedure to check it, I zoned in on the VSM being the problem thru reading posts on this, and other websites - just do searches under VSM or GEM and see what pops up.....
Cost was about $120 bucks for the VSM from FTE PartsGuy (that was the cheapest price I found by a mile !) AND $145 for the Stealership to reprogam it -took them all but about 20 minutes!
Good luck...
Mark
02 7.3 4x4 DRW Lariat CC
The issue was a busted/fried VSM (Vehicle Security Module) Since your truck is a '02 it should have a VSM (not a GSM - from earlier trucks...) located behind the radio, mounted on the inside of the firewall - a small black box with three plugs - took me about an hour to get access to it. Don't know if there is a procedure to check it, I zoned in on the VSM being the problem thru reading posts on this, and other websites - just do searches under VSM or GEM and see what pops up.....
Cost was about $120 bucks for the VSM from FTE PartsGuy (that was the cheapest price I found by a mile !) AND $145 for the Stealership to reprogam it -took them all but about 20 minutes!
Good luck...
Mark
02 7.3 4x4 DRW Lariat CC
Junior User
Joined: Oct 2008
Posts: 51
Likes: 0
In my case they worked only if:
1. I was turning them on and off with the switch on the dash.
2. When I removed the keys from the ignition and opened the door. (they would go out as they should a few moments later).
They would not work just when I opened the doors....
I do remember reading a similar issue as yours someone had on one of the forums (not sure which one - sorry) and remember someone suggested/asked if the polarity on the wires for the were switched - that did not make too much sense to me so I did not read much further than that.....
Mark
1. I was turning them on and off with the switch on the dash.
2. When I removed the keys from the ignition and opened the door. (they would go out as they should a few moments later).
They would not work just when I opened the doors....
I do remember reading a similar issue as yours someone had on one of the forums (not sure which one - sorry) and remember someone suggested/asked if the polarity on the wires for the were switched - that did not make too much sense to me so I did not read much further than that.....
Mark
Fleet Mechanic
Joined: Feb 2005
Posts: 1,797
Likes: 1
From: Northern Colorado
The original VSM's in the 2002 are notoriously BAD. The new ones have a different part number, upgraded in 2003 (and you get to pay for it).
The dealer has to scan your old one while connected, install the new one and reprogram it with your scanned data.
The dealer has to scan your old one while connected, install the new one and reprogram it with your scanned data.
Trending Topics
Junior User
Joined: Oct 2008
Posts: 51
Likes: 0
All of the research I have done during the time I had the issue with my VSM involved 2002 year trucks. I don't think I saw any 2003 or later trucks.
In my case the old VSM was so bad/fried the dealer was not able to download the data into the new one. The build sheet I had, complements FTE PartsGuy, was used to restore the data !
Mark
In my case the old VSM was so bad/fried the dealer was not able to download the data into the new one. The build sheet I had, complements FTE PartsGuy, was used to restore the data !
Mark
FTE Stories
Ford Trucks for Ford Truck Enthusiasts
Rezvani's Latest Post-Apocalytic Monster Is a Ford F-150 Raptor Underneath
Verdad Gallardo
Top 10 Most Expensive Ford Trucks Ever Sold on Bring a Trailer
Joe Kucinski
2027 Ford Super Duty Buyer's Guide (Every Model, Engine, & Package)
Brett Foote
Top 10 Ford Truck Tragedies
Joe Kucinski
AEV FXL Super Duty - the Super Duty Raptor Ford Doesn't Make
Brett Foote
Lobo Vs Lobo: Proof the F-150 Lobo Should Be Even Lower!
Michael S. Palmer
Ford's 2001 Explorer Sportsman Concept Looks For a New Home
Verdad Gallardo
10 Best Ford Truck Engines We Miss the Most!
Joe Kucinski
2026 Shelby F-150 Off-Road: Better Than a Raptor R?
Brett Foote
Hotshot
Joined: Jan 2008
Posts: 13,144
Likes: 11
From: Rochdale MA
Well then why is it when i take the switch out and use it manualy it works the way it should. If it is the GEM where is it behind the fuse box? Is it kinda like a dumbed down body controler? Im used to body controler issues since i do alot of ESC work on international trucks. Im new to chassis work on superdutys so i dont know my way around yet. Do you know of any ways to check this? Any hints to give?
I can't find the other thread but it did turn out to be a VSM issue. The signal from the door switch is "routed" through the VSM for the interior lights.
Thread Starter
|
Senior User
Joined: Apr 2009
Posts: 301
Likes: 0
From: Scenery hill,Pa.
Well im going with what you guys have said. It seems to be the issue. Im going to to check one more thing before i do that. Going to pull the switches out and see if by manually oushing them if it works right. I tried it once but i want to check it again. How much is the VSM? I know it will cost 90 for ford for minum of 1 hour computer time.
Mountain Pass
Joined: Jul 2006
Posts: 178
Likes: 0
From: Franklin, WI
