Anyone need a cap for a ranger longbed? its grey and has the yakima rack on top locking rear hatch and right side hatch.. slider on left its a leer fiberglass cap ill take $200 for it.. must be picked up in Deposit NY ( near Hancock PA) on a day when im up there

 

i have a late 80's early 90's 8ft bed minor rust at the wheel fenders its set up for dual tanks im asking $100 for it PM me if interested

 

REESE 5th WHEEL KWIK-SLIDE HITCH w/BED RAILS and HARDWARE. Very little use. 16K RATED. $300.00 Send PM if interested.

 

Hey guys I got all the stock suspension here sitting in my garage, my 04 has the tow package, I dont know if that would matter to anyone. I was told you may be able to use the springs to level an Excursion, but IDK. I also got 6" Skyjacker rear lift blocks.
The springs will just cost ya a 30 pack of Budweiser select (which of course I will split with you when you pick them up )
as for the blocks.......a 6 pack plus shipping if you want them delivered LOL

 

Hey anybody out there looking for 73-79 stuff ? I've got a bunch to sell or trade.Did I mention cheap ?

1 - C6 auto for a 4x2 truck with 351M/400, 429/460 bell.Worked when parked.
1 - C6 auto for a 4x2 truck with 6 cyl or small block V8.Worked when parked.
1 - D60 rear for a 4x2 truck. 3.54 ratio.No posi.
3 - 351M/400 bell housings.
1 - 79 grille.Not show quality but nice.
1 - brown dash pad.No cracks.
2 - left fenders.No rust.
1 - right fender.No rust.
1 - tail gate for Styleside bed.Has a slight bow but no rust.
1 - right door.Fair shape.Good for daily driver.

If anyone is interested let me know.
Thanks for looking.

 

Hey any you pa guys need parts small or large , I have a add on the classifieds. Just wanted to let the local guys know first .

 

looking 4 2000 n up rear springs f- 250 350 stock or lifted

 

I got all the stock suspension stuff for my '04 F250 got all 4 leafs, shocks and any brackets that were replaced when I put the 6 inch lift on

 

nice truck! but your a little too far from me , about 300 miles too far, thanks though.

 

https://www.ford-trucks.com/classifi...ate/1143770423

thanks for looking

 

Hypertech power programmer for a 99-02 or 03 F-250 with the 5.4 v8. $200 shipped. OBO

 

5.4 v8 99,000 miles engine runs good Tranny needs a sensor Has a few dents on it and some surface scratches. Gooseneck hitch 4x4 asking $5900 New true flow air filter, flow master exhaust, o2 sensors, spark plugs, and some suspension parts on the front end.

 

looking for someone close to oxford pa with a front driveshaft from a 250 for sale

 

My truck was run into today . If it wasn't for the DeeZee Fx stainless running board pushing forward anf hitting tire would have really caved my side in.

So If you Have any DeeZee boards with rubber molded front for a 92-97 F150+ Sc/crew/bronco (I'll get em welded ) I have a supercab

Or A nice set of boards in general let me know.

These boards have been on 5 of my trucks and looked new . I feel bad because my father bought them for me before he got sick.
I'm not getting $ for them because they are after market. And the $300+ Is out of question right now.

 

i am trying to find the famous 402040 seats in grey for my truck, those or the factory buckets would be nice, the bench is quite a pain in the butt