Installing a tachometer
Thread Starter
|
Junior User
Joined: May 2005
Posts: 56
Likes: 0
Installing a tachometer
Im going to install a tach in my truck hopefully today (85 f150 I6 etc...) and im just wondering whats the best way to go about it. Im probably just gonna get a cheapo autometer tach. I was going to check my haynes manual for any wires to tap into but i just wanted to know if there was an easier way.
Elder User
Joined: Jul 2004
Posts: 620
Likes: 1
From: Toronto, ON
I bought a cheapo one, and I tapped into the wire harness for the dash cluster. Using wiring tables from my Haynes manual, I was able to identify a (+) 12v, ground, tach signal, and interior light switched (+) 12v wire to splice (all four connections needed to run the tach!). It was pretty easy 
Check my gallery, I think I have pics of the process. If not I can add some
The hardest part was learning how to properly/easy remove the light control ****!
Check my gallery, I think I have pics of the process. If not I can add some The hardest part was learning how to properly/easy remove the light control ****!
Postmaster
Joined: Feb 2003
Posts: 3,439
Likes: 6
From: Spokane WA
these jeep tachs work great for a 300.
JC Whitney part # ZX476802Y
0-6000 rpm
if you don't wind it out often this works great too
JC Whitney part # ZX133677X
0-4000 rpm
JC Whitney part # ZX476802Y
0-6000 rpm
if you don't wind it out often this works great too
JC Whitney part # ZX133677X
0-4000 rpm
Last edited by oldhalftons; May 17, 2005 at 07:34 PM.
Senior User
Joined: Dec 2004
Posts: 233
Likes: 0
From: centeral Ohio
Yah lol mine go's to 8k rpm it's a little over what i rev you could say i guess. I think my dad forgot to take in to consideration it's not a built 302 seeing 7500 rpms non stop. More like a 1988 300-6 efi stock /w up to 4.5k or so max rpms lol.
Elder User
Joined: Jul 2004
Posts: 620
Likes: 1
From: Toronto, ON
Originally Posted by Gerry Lutz Jr.
Yah lol mine go's to 8k rpm it's a little over what i rev you could say i guess. I think my dad forgot to take in to consideration it's not a built 302 seeing 7500 rpms non stop. More like a 1988 300-6 efi stock /w up to 4.5k or so max rpms lol.
I cringe when I get near 3k because it sounds like the world is coming to and end!
Trending Topics
Thread Starter
|
Junior User
Joined: May 2005
Posts: 56
Likes: 0
thanks guys i hooked it up last night. Runs great. I roughly hooked it up since i didnt have the time to find a proper place to find a power source and a ground. Going to finish it off tonight.
FTE Stories
Ford Trucks for Ford Truck Enthusiasts
10 Things Every Truck Owner NEEDS (2026 Edition)
Michael S. Palmer
Rezvani's Latest Post-Apocalyptic Monster Is a Ford F-150 Raptor Underneath
Verdad Gallardo
Top 10 Most Expensive Ford Trucks Ever Sold on Bring a Trailer
Joe Kucinski
2027 Ford Super Duty Buyer's Guide (Every Model, Engine, & Package)
Brett Foote
Top 10 Ford Truck Tragedies
Joe Kucinski
AEV FXL Super Duty - the Super Duty Raptor Ford Doesn't Make
Brett Foote
Lobo Vs Lobo: Proof the F-150 Lobo Should Be Even Lower!
Michael S. Palmer
Ford's 2001 Explorer Sportsman Concept Looks For a New Home
Verdad Gallardo
10 Best Ford Truck Engines We Miss the Most!
Joe Kucinski
Thread Starter
|
Junior User
Joined: May 2005
Posts: 56
Likes: 0
Originally Posted by Roushians
Where did you mount yours? I mounted mine on top of the dash LOL
It looks quite hot-rod-ish
LOLIt looks quite hot-rod-ish
Senior User
Joined: Dec 2004
Posts: 233
Likes: 0
From: centeral Ohio
I didn't say i rev mine to 4,500 i just said redline is around there. Then again when i first test drove it i revved it to 5k not knowing what was under the hood at the time. It realy did sound like it was going to fall apart lol. Mine does see 3500 rpms though and often (only in 2nd gear) since i run a granny 4 spd which has the gaping hole between 2nd and 3rd gears.
Posting Guru
Joined: Jul 2003
Posts: 2,454
Likes: 1
From: Adams TN
Gerry, I hear you about that gap.
I have a NP 435 and the 3-4 gap is horrable. i shift to 4th at 20mph @2100RPM and when i get to 4th it is @ 1100RPM. I wish i had a Gear Vendor so i could split that shift and not have to run 65 at the redline.
I installed a factory tach. It works better in hot weather. and Intermitantly but i just took the printed circuit and tach and just swaped it out. Looks better than that dectative crap they put there.
DT
I have a NP 435 and the 3-4 gap is horrable. i shift to 4th at 20mph @2100RPM and when i get to 4th it is @ 1100RPM. I wish i had a Gear Vendor so i could split that shift and not have to run 65 at the redline.
I installed a factory tach. It works better in hot weather. and Intermitantly but i just took the printed circuit and tach and just swaped it out. Looks better than that dectative crap they put there.
DT
Senior User
Joined: Dec 2004
Posts: 233
Likes: 0
From: centeral Ohio
Wow i think that may even be a worse gap than my 2nd to 3rd. Mine usually drops from 2.5k rpms to about 1.25k shifting from 2nd to 3rd. I'd go drive it and tell you for sure but, it's the cleanest it's ever been and i'm avoiding driving because it's ready to sell that and i have the "un luck of the irish" stuff always brakes when i drive it lol. Not realy sure why either i'm not that mean to it and take very good care of it. I have about 3,000 in to it in repairs and such since i've bought it pretty easily i would expect.
Posting Guru
Joined: Apr 2003
Posts: 1,153
Likes: 1
From: Venezuela
Originally Posted by Roushians
4.5k!! holy I cringe when I get near 3k because it sounds like the world is coming to and end!
I cringe when I get near 3k because it sounds like the world is coming to and end!
Posting Guru
Joined: Apr 2003
Posts: 1,153
Likes: 1
From: Venezuela
Originally Posted by Roushians
Where did you mount yours? I mounted mine on top of the dash LOL
It looks quite hot-rod-ish
LOLIt looks quite hot-rod-ish
