'97 psd stalling problems
Thread Starter
|
New User
Joined: Oct 2000
Posts: 2
Likes: 0
'97 psd stalling problems
Can any one help? I have a '97 f-250hd psd 4x4 automatic. My truck occasionaly stalls while decelerating at slower speeds. Also has momentarily cutout while under load climbing a grade. 1 more problem. All of a sudden when I hook up my trailer with electric brakes the engine dies every time I step on the brake. Any suggestions on how to troubleshoot, or where to take it? Any suggestions are appreciated.
Laughing Gas
Joined: Jun 1999
Posts: 903
Likes: 0
From: Banning CA
'97 psd stalling problems
Check body ground conections. Also you may have a bad camshaft position sensor. But the best is to have it checked out.
Dave
http://a2ztowing.homestead.com/a2ztowing.html
Dave
http://a2ztowing.homestead.com/a2ztowing.html
New User
Joined: May 2000
Posts: 9
Likes: 0
'97 psd stalling problems
I have seen this concern more than once. yes you
could have a bad cam position sensor but i think
it may be a trans. problem. service the tranny. a clogged tranny filter will stall the engine
at slow speeds while braking. sounds crazy but
ford has a tsb out on this and I have resolved
a few of these concerns that way. hope you solve it
scott
could have a bad cam position sensor but i think
it may be a trans. problem. service the tranny. a clogged tranny filter will stall the engine
at slow speeds while braking. sounds crazy but
ford has a tsb out on this and I have resolved
a few of these concerns that way. hope you solve it
scott
Cargo Master
Joined: Jul 2010
Posts: 3,014
Likes: 115
spiziali, I think your problem sounds like a bad CPS. Get a new Motorcraft (dark grey with purple o-ring). You should start there because they're inexpensive to replace. Just don't pay $200 at a dealership like they tried to get me to do.
Servicing the transmission is never a bad idea. That should be part of regular service, and if you haven't done that in a while, I would go ahead and do that too, if I were you.
Servicing the transmission is never a bad idea. That should be part of regular service, and if you haven't done that in a while, I would go ahead and do that too, if I were you.
Cargo Master
Joined: Jul 2010
Posts: 3,014
Likes: 115
Yeah, the filter's right there inside the pan. Make sure the old o-ring comes off with the old filter and doesn't get stuck up in that tube.
Trending Topics
Hotshot
Joined: Aug 2006
Posts: 10,764
Likes: 39
No Trans expert here , but it sounds like the TC is staying locked ...
FTE Stories
Ford Trucks for Ford Truck Enthusiasts
2027 Ford Super Duty Buyer's Guide (Every Model, Engine, & Package)
Brett Foote
Top 10 Ford Truck Tragedies
Joe Kucinski
AEV FXL Super Duty - the Super Duty Raptor Ford Doesn't Make
Brett Foote
Lobo Vs Lobo: Proof the F-150 Lobo Should Be Even Lower!
Michael S. Palmer
Ford's 2001 Explorer Sportsman Concept Looks For a New Home
Verdad Gallardo
10 Best Ford Truck Engines We Miss the Most!
Joe Kucinski
2026 Shelby F-150 Off-Road: Better Than a Raptor R?
Brett Foote
2027 Super Duty Carhartt Package First Look: 12 Things You NEED to Know!
Michael S. Palmer
10 Most Surprising 2026 Ford Truck Features!
Joe Kucinski
Post Fiend
Joined: Mar 2007
Posts: 26,966
Likes: 50
From: Texas
My money says spiziali doesn't even own that truck anymore.
Powerstroked XLT, why are you starting out in 1st and then shifting into D? I would agree with Rick about the torque converter sounding like it's not unlocking, but perhaps if we knew more about what else was going on we might be able to offer more suggestions. Also, any chips or mods to your truck?
Powerstroked XLT, why are you starting out in 1st and then shifting into D? I would agree with Rick about the torque converter sounding like it's not unlocking, but perhaps if we knew more about what else was going on we might be able to offer more suggestions. Also, any chips or mods to your truck?
Freshman User
Joined: Feb 2011
Posts: 45
Likes: 0
I posted problem a few weeks ago and didn't hear much, so I was poking around on some old post.....would be great to hear some suggestions.
When I have going down a steep grade at slow speeds (typically residential) and have the tranny manually shifted into first gear (1500 rpm range at 5-10 mph), reach the bottom and go to shift it into drive, the RPMs just dive and the truck basically shuts off and will re-start just fine. I can manually shift though all the gears fine, and if I leave it in first gear, come to a complete stop, then put it in drive it does not die. I cannt figure out why it basically turns off if I put it back in drive under that circumstance only......it seems to be related to the high RPM or exhaust back preasure?
Truck has a new CPS, 150k miles, turbo back exhaust (no cat) and has a chip.
Any ideas?.....
When I have going down a steep grade at slow speeds (typically residential) and have the tranny manually shifted into first gear (1500 rpm range at 5-10 mph), reach the bottom and go to shift it into drive, the RPMs just dive and the truck basically shuts off and will re-start just fine. I can manually shift though all the gears fine, and if I leave it in first gear, come to a complete stop, then put it in drive it does not die. I cannt figure out why it basically turns off if I put it back in drive under that circumstance only......it seems to be related to the high RPM or exhaust back preasure?
Truck has a new CPS, 150k miles, turbo back exhaust (no cat) and has a chip.
Any ideas?.....
Cargo Master
Joined: Jul 2010
Posts: 3,014
Likes: 115
Edit: I was ten years old when this thread was started, lol.
Post Fiend
Joined: Mar 2007
Posts: 26,966
Likes: 50
From: Texas
Reminds me of the old joke where I went to the Doctor and said, Doc, it hurts when I do this. The doc replied, then don't do that. 
I don't think your problem is back pressure related. Lots of compression in the diesel engine. I'd start experimenting and see how you can change it. Try accelerating a little before shifting. Try shifting into 2 for a bit then up to drive. Try shifting into Neutral first, then back into Drive. Remove the chip and see if that changes anything.
I don't think your problem is back pressure related. Lots of compression in the diesel engine. I'd start experimenting and see how you can change it. Try accelerating a little before shifting. Try shifting into 2 for a bit then up to drive. Try shifting into Neutral first, then back into Drive. Remove the chip and see if that changes anything.
