Throttle Problem
Thread Starter
|
Elder User
Joined: Mar 2003
Posts: 687
Likes: 0
From: Medford, OR
Throttle Problem
While I am accelerating at what I would call about 1/4-1/2 throttle there seems to be some hesitation. If I give it just a little more gas it accelerates very smoothly through. There seems to be a point where it just isn't getting enough gas to accelerate smoothly. What would be the first thing to check on this? My Bronco is a 93 Custom with the E40d
Post Fiend
Joined: Nov 2002
Posts: 9,987
Likes: 7
From: Memphis, TN
Throttle Problem
Pull the codes and test the Throttle Position Sensor by the Haynes manual procedure.
Thread Starter
|
Elder User
Joined: Mar 2003
Posts: 687
Likes: 0
From: Medford, OR
Throttle Problem
I am trying to pull the codes and have a few questions. The page lists two methods. Which one should I use? Is one easier than the other? Also, the diagram shows the seperate little plug with an arrow going to one of the pins. Do those need to be connected or is that only for the KOEO test? Any extra help would be much appreciated.
Post Fiend
Joined: Nov 2002
Posts: 9,987
Likes: 7
From: Memphis, TN
Throttle Problem
Warm the engine up & fix any problems you can identify. Tune it according to the emissions sticker, then turn it off. Put a jumper wire (or paperclip) from the single wire connector to the top R terminal of the 6-position connector. Turn the key to RUN and observe the ENG (or EMISSIONS) light on the dash. Ignore the quick flash(es) that occur within 2 seconds of turning the key to RUN. Each code will flash out twice. Ignore the single flash separated by ~6 sec pauses before & after, then observe the second group of codes. After they're finished, turn the key off & back on and record the codes. (The first time was for practise, but if you got them all correctly written down, you don't have to do it the second time.) When you're sure you have all the codes recorded, trigger them to flash out one more time, and remove the jumper wire WHILE they're flashing out - this clears the codes from memory.
Thread Starter
|
Elder User
Joined: Mar 2003
Posts: 687
Likes: 0
From: Medford, OR
Throttle Problem
I cleared the codes and it is still flashing out what seems to be a 33 code twice when I do the test. Am I just reading it wrong or is this actually something I should look into? The check engine light is not on or anything. Thanks.
Post Fiend
Joined: Nov 2002
Posts: 9,987
Likes: 7
From: Memphis, TN
Throttle Problem
You're reading it wrong - that's "1-1-1" flashing out twice for the continuous codes, then again for KOEO. Code 111 is all clear. Test drive it for a day or so and pull them again to see if any problems reappear.
Trending Topics
Thread Starter
|
Elder User
Joined: Mar 2003
Posts: 687
Likes: 0
From: Medford, OR
Throttle Problem
Ok, thanks a lot, Steve. I was thinking that was most likely the case. Thanks for having patience with us newbies 
FTE Stories
Ford Trucks for Ford Truck Enthusiasts
2027 Ford Super Duty Buyer's Guide (Every Model, Engine, & Package)
Brett Foote
Top 10 Ford Truck Tragedies
Joe Kucinski
AEV FXL Super Duty - the Super Duty Raptor Ford Doesn't Make
Brett Foote
Lobo Vs Lobo: Proof the F-150 Lobo Should Be Even Lower!
Michael S. Palmer
Ford's 2001 Explorer Sportsman Concept Looks For a New Home
Verdad Gallardo
10 Best Ford Truck Engines We Miss the Most!
Joe Kucinski
2026 Shelby F-150 Off-Road: Better Than a Raptor R?
Brett Foote
2027 Super Duty Carhartt Package First Look: 12 Things You NEED to Know!
Michael S. Palmer
