Toolbox and Gooseneck
Thread Starter
|
Laughing Gas
Joined: Aug 2010
Posts: 852
Likes: 12
From: Kentucky
Toolbox and Gooseneck
I've always run pintle hitch trailers for work, but I like the idea of the extra ton of cargo with the gooseneck. I have a short bed and after looking over the idea today it seems like if I used a gooseneck with my toolbox in the rear, if I were to get in a severe angle with the truck and trailer ( \/ , that kind of angle
) that I run the risk of smashing the neck of the trailer into the toolbox? I'd say there is maybe two feet of clearance there.
) that I run the risk of smashing the neck of the trailer into the toolbox? I'd say there is maybe two feet of clearance there.
Lead Driver
Joined: Jan 2010
Posts: 6,600
Likes: 84
I personally wouldn't hook up a gooseneck and have a toolbox on my truck (SB).
Maybe some do it but I am sure I would forget one day and cause a problem.
Edit: I'm also thinking along the lines of an equipment gooseneck trailer not something as big as a horse trailer which I wouldn't even consider with a toolbox.
Maybe some do it but I am sure I would forget one day and cause a problem.
Edit: I'm also thinking along the lines of an equipment gooseneck trailer not something as big as a horse trailer which I wouldn't even consider with a toolbox.
Senior User
Joined: Mar 2009
Posts: 345
Likes: 0
I'd think you'd probably have an issue there, my buddy has a long bed 350 and hit his 5ver on his tool box within an hour of buying the trailer. Maybe yours won't hit but just watch it real close with the firt tow
Senior User
Joined: Aug 2010
Posts: 317
Likes: 0
i have one in my bed and towed for over 6 yrs with it. i can tow a flatbed goose-neck with no problems, but when i tow our big cow trailer, it has a weird front piece on the nose and causes me to take the tool box out.
the middle pic is very similar to our cow trailer, ours is 30ft with dual jacks...
Livestock Trailers by M.H. EBY - Ruff Neck
a flatbed would have to be cut alomost 90 degrees for it to hit my toolbox..
forgot to say i have a low profile toolbox, so that helps alittle bit...
the middle pic is very similar to our cow trailer, ours is 30ft with dual jacks...
Livestock Trailers by M.H. EBY - Ruff Neck
a flatbed would have to be cut alomost 90 degrees for it to hit my toolbox..
forgot to say i have a low profile toolbox, so that helps alittle bit...
Cargo Master
Joined: Aug 2010
Posts: 3,229
Likes: 64
I took my saddle type tool box off and replaced it with an "in the bed" box on my old SB and had no problems with a conventional 5th wheel.
Most goose-necks (I had an adepter for my truck) would be OK too, except the one pictured above.
Most goose-necks (I had an adepter for my truck) would be OK too, except the one pictured above.
Thread Starter
|
Laughing Gas
Joined: Aug 2010
Posts: 852
Likes: 12
From: Kentucky
Anybody try one of these?
"Popup Gooseneck nine inch trailer extension for shortbed trucks, Horse Trailers, gooseneck hitch, Race Car Trailers, shortbed hitch, short bed truck hitch,Gooseneck conversion,gooseneck extension, gooseneck adaptor,5th wheel conversion,Popup Hitch,
I'm looking at a flatbed trailer for equipment and such.
"Popup Gooseneck nine inch trailer extension for shortbed trucks, Horse Trailers, gooseneck hitch, Race Car Trailers, shortbed hitch, short bed truck hitch,Gooseneck conversion,gooseneck extension, gooseneck adaptor,5th wheel conversion,Popup Hitch,
I'm looking at a flatbed trailer for equipment and such.
Thread
Thread Starter
Forum
Replies
Last Post
