07' won;t stay running after undercoating with fluid film!!!!
#1
07' won;t stay running after undercoating with fluid film!!!!
Began doing this on sunday and just finished up last night. Truck starts and runs for a bit then stalls. Here is what I did in this order:
1.) Washed truck sundday with purple power and a garden hose. I washed the wheel wells frame and underside, but DID NOT wash the engine at all.
2.) Painted the frame and wheel wells with black paint.
3.) Applied 1/2 gallon or so of fluid film all over the bottom of the truck everywhere I can. Again NOT the engine bay.
Any idea where to start. When it stalled, I can restart eevery time by waiting 3-5 minutes. It was 13 degrees F last night, so i suspect fuel lines may be freezing but not sure.
1.) Washed truck sundday with purple power and a garden hose. I washed the wheel wells frame and underside, but DID NOT wash the engine at all.
2.) Painted the frame and wheel wells with black paint.
3.) Applied 1/2 gallon or so of fluid film all over the bottom of the truck everywhere I can. Again NOT the engine bay.
Any idea where to start. When it stalled, I can restart eevery time by waiting 3-5 minutes. It was 13 degrees F last night, so i suspect fuel lines may be freezing but not sure.
#2
Began doing this on sunday and just finished up last night. Truck starts and runs for a bit then stalls. Here is what I did in this order:
1.) Washed truck sundday with purple power and a garden hose. I washed the wheel wells frame and underside, but DID NOT wash the engine at all.
2.) Painted the frame and wheel wells with black paint.
3.) Applied 1/2 gallon or so of fluid film all over the bottom of the truck everywhere I can. Again NOT the engine bay.
Any idea where to start. When it stalled, I can restart eevery time by waiting 3-5 minutes. It was 13 degrees F last night, so i suspect fuel lines may be freezing but not sure.
1.) Washed truck sundday with purple power and a garden hose. I washed the wheel wells frame and underside, but DID NOT wash the engine at all.
2.) Painted the frame and wheel wells with black paint.
3.) Applied 1/2 gallon or so of fluid film all over the bottom of the truck everywhere I can. Again NOT the engine bay.
Any idea where to start. When it stalled, I can restart eevery time by waiting 3-5 minutes. It was 13 degrees F last night, so i suspect fuel lines may be freezing but not sure.
#5
I am forever in your debt guys......the FDM rotted off the crossmemebr was was laying on top of the tire. It was filled with grit, water, fluid film, and who knows what else.
How can a formal complaint be made, like how all the people complained about the fuel tank straps on the older trucks? This design makes me think of general motors, not ford. This is disgusting.
How can a formal complaint be made, like how all the people complained about the fuel tank straps on the older trucks? This design makes me think of general motors, not ford. This is disgusting.
#6
fordiesel69;14835071]I am forever in your debt guys......the FDM rotted off the crossmemebr was was laying on top of the tire. It was filled with grit, water, fluid film, and who knows what else.
Thread
Thread Starter
Forum
Replies
Last Post
bob.p
1987 - 1996 F150 & Larger F-Series Trucks
4
08-12-2014 09:28 AM
93blueoval f-250
Fuel Injection, Carburetion & Fuel System
3
03-19-2007 11:33 AM
mike L
1987 - 1996 F150 & Larger F-Series Trucks
24
09-26-2004 09:16 AM
bcooke333
1987 - 1996 F150 & Larger F-Series Trucks
4
09-09-2003 08:45 AM