New 71
#196
#197
Well just did the rocker panel delete trick, going to add some rock sliders/re-tie the roll cage (front and rear) to the frame and incorporate the sliders all in one package deal this weekend. And make it so I have a side mounted receiver hitch point, so I can move my winch to the side. BAM.
This was a long awaited project, I am far from done. This was just as the pieces hit the driveway. So mores pics to follow. Yes I still have some "low hanging fruit" to trim off. lol
This was a long awaited project, I am far from done. This was just as the pieces hit the driveway. So mores pics to follow. Yes I still have some "low hanging fruit" to trim off. lol
#198
what parts?
not sure it'll ever C doors again but hope whatever U do allows them to B mounted again.
Always like what U come up with & have confidence you'll tie everything to the frame. Saw one where the legs went right thru the floor & were out bout 2 - 3 feet after a flip. Pointless, cosmetic only, worthless, dangerous, dumb; better stop - might say the wrong thing…
Always like what U come up with & have confidence you'll tie everything to the frame. Saw one where the legs went right thru the floor & were out bout 2 - 3 feet after a flip. Pointless, cosmetic only, worthless, dangerous, dumb; better stop - might say the wrong thing…
#199
Good advice and thanks for the vote of confidence.... Yes I will be able to remount my fiberglass inserts with some vinyl 1/2 doors to try and keep some warmth inside it.
I am taking it to my buddies welding shop this sat and we are making some 2x3 (thick wall) rectangle tubing sliders, then tie it all together.
More pics to come. I got the idea w/pics off the ClassicBronco site. http://classicbroncos.com/tech/cutting-off-rockers And http://classicbroncos.com/forums/sho...d.php?t=214227
And a few others, and a big thanks to all. http://broncofix.com/viewtopic.php?t=274021&view=next
I am taking it to my buddies welding shop this sat and we are making some 2x3 (thick wall) rectangle tubing sliders, then tie it all together.
More pics to come. I got the idea w/pics off the ClassicBronco site. http://classicbroncos.com/tech/cutting-off-rockers And http://classicbroncos.com/forums/sho...d.php?t=214227
And a few others, and a big thanks to all. http://broncofix.com/viewtopic.php?t=274021&view=next
#200
Day 2...Here is what we got done today, Bronco off the trailer at the shop at 0800, job done both sides and back on and home by 545.
We got all the rest of the underside of the body cut and prepped, rock sliders built, with the center receiver hitch idea and the roll cage/frame tie-ins X4 all completed.
I can hang the winch off either side, make some QD steps, put my farm jack in the hole and lift the side of the Bronco off the ground.
Opinions, questions, input? All welcome.
We got all the rest of the underside of the body cut and prepped, rock sliders built, with the center receiver hitch idea and the roll cage/frame tie-ins X4 all completed.
I can hang the winch off either side, make some QD steps, put my farm jack in the hole and lift the side of the Bronco off the ground.
Opinions, questions, input? All welcome.
#201
new rock sliders
I have cooper running back to my rear (& frnt) reciever to locate the winch either end. I guess I could head it off on that 1 side & run some over to the other side but for the expense I can't see it. How often does one need to winch from the side?
Interested in the step & jack point from that iron 2 by 4! (I got a 6 ft piece, probably only 1/2 the needed stock).
#202
Here is the final none painted product, the roll cage front down bar floor plates were already welded to the floor pans (which is 3/16 tread plate), the rears were not.
So I only grade 8 bolted them to the bottom plates (supported by the rock rails front and rear)...and did not weld the underside rock rail plate to the under side of the tread plate....I might in the future.
I did one weld pass on the one side of the dvrs side plate. Since I was missing some body panel and could access is very easy. You can see it in the 3rd pic.
It is a standard receiver size middle tube, so I can fab any kind of step for the wife. The farm jack lift point will fit in there just fine. Wiring the winch is on the list (I have QD ended jumper cables for now) so I can hot winch it truck to truck or to my trailer.
I am going to leave enough cable to run it to the front/rear and side. But only have one set of cables connected to one power source with QD's on the end.
So I only grade 8 bolted them to the bottom plates (supported by the rock rails front and rear)...and did not weld the underside rock rail plate to the under side of the tread plate....I might in the future.
I did one weld pass on the one side of the dvrs side plate. Since I was missing some body panel and could access is very easy. You can see it in the 3rd pic.
It is a standard receiver size middle tube, so I can fab any kind of step for the wife. The farm jack lift point will fit in there just fine. Wiring the winch is on the list (I have QD ended jumper cables for now) so I can hot winch it truck to truck or to my trailer.
I am going to leave enough cable to run it to the front/rear and side. But only have one set of cables connected to one power source with QD's on the end.
#204
#206
#207
#208
#209
Tested the high lift jack hitch point ability, got both tires off the ground. I am going to get an Alien jack base...or try a little fabrication of my own.
Alien Jack Base for Farm Jack | Hard Core Trail Gear, LLC
I also removed the spare tire baja mount. it was a total view blocker for backing up.
Alien Jack Base for Farm Jack | Hard Core Trail Gear, LLC
I also removed the spare tire baja mount. it was a total view blocker for backing up.
#210
"Tested the high lift jack hitch point ability, got both tires off the ground. I am going to get an Alien jack base...or try a little fabrication of my own.
I also removed the spare tire baja mount. it was a total view blocker for backing up.
Thanks 4 da link, I'd see that somewhere B4. Pretty aggressive. Seen it in use?
Looks like ur near the end of that jack w/da lift, Irocks, etc.
Red is gettin closer'n closer to Hillbilly Bug every day!
Never thought of usin a reciever as a jack point
8^0
Last or nxt 2 last pic still shows spare mount, sure it's gone? send it my way?
I also removed the spare tire baja mount. it was a total view blocker for backing up.
Thanks 4 da link, I'd see that somewhere B4. Pretty aggressive. Seen it in use?
Looks like ur near the end of that jack w/da lift, Irocks, etc.
Red is gettin closer'n closer to Hillbilly Bug every day!
Never thought of usin a reciever as a jack point
8^0
Last or nxt 2 last pic still shows spare mount, sure it's gone? send it my way?