to bad no member live close to where I live
or it would be "Work on your truck weekend"
Mini-Mini-Mini ManTown
Thread Starter
|
Fleet Mechanic
Joined: Dec 2005
Posts: 1,254
Likes: 120
Mini-Mini-Mini ManTown
Ok here is the deal....
We have two FTE members that need balljoints done on their vehicles.
1. David (aawlberninf350) needs to finish the job on his passenger side from the last Mantown at Andy's
2. Willis (Leeroy7.3) need to have both sides replaced.
I know this is last minute but though if any other FTE members in N.California wanted to join us this Saturday 1/30/2016 you are welcome. We didn't know if the weather would allow us to do this work but it looks like we will have good weather on Saturday.
Let me know if anyone is interested and I can send the details. It will take place in the Contra Costa area.
I plan on adding gauges to my Excursion and I also picked up a DP tuner.
Tim M
We have two FTE members that need balljoints done on their vehicles.
1. David (aawlberninf350) needs to finish the job on his passenger side from the last Mantown at Andy's
2. Willis (Leeroy7.3) need to have both sides replaced.
I know this is last minute but though if any other FTE members in N.California wanted to join us this Saturday 1/30/2016 you are welcome. We didn't know if the weather would allow us to do this work but it looks like we will have good weather on Saturday.
Let me know if anyone is interested and I can send the details. It will take place in the Contra Costa area.
I plan on adding gauges to my Excursion and I also picked up a DP tuner.
Tim M
Thread Starter
|
Fleet Mechanic
Joined: Dec 2005
Posts: 1,254
Likes: 120
Ya a bit short notice. We were not sure the weather was going to allow us to do any work but as I mentioned looks like it will.
I am about 30 miles east of San Francisco, specifically in Concord.
Tim M
I am about 30 miles east of San Francisco, specifically in Concord.
Tim M
More Turbo
Joined: Jun 2010
Posts: 546
Likes: 1
From: reedsport
Trending Topics
Thread Starter
|
Fleet Mechanic
Joined: Dec 2005
Posts: 1,254
Likes: 120
Those things (kids) get in the way sometimes.
Looks like the weather may not be cooperating with us for Saturday. We are going to tough it out unless it becomes too much. We may have to use pop-ups for cover.
Tim M
Looks like the weather may not be cooperating with us for Saturday. We are going to tough it out unless it becomes too much. We may have to use pop-ups for cover.
Tim M
FTE Stories
Ford Trucks for Ford Truck Enthusiasts
10 Things Every Truck Owner NEEDS (2026 Edition)
Michael S. Palmer
Rezvani's Latest Post-Apocalyptic Monster Is a Ford F-150 Raptor Underneath
Verdad Gallardo
Top 10 Most Expensive Ford Trucks Ever Sold on Bring a Trailer
Joe Kucinski
2027 Ford Super Duty Buyer's Guide (Every Model, Engine, & Package)
Brett Foote
Top 10 Ford Truck Tragedies
Joe Kucinski
AEV FXL Super Duty - the Super Duty Raptor Ford Doesn't Make
Brett Foote
Lobo Vs Lobo: Proof the F-150 Lobo Should Be Even Lower!
Michael S. Palmer
Ford's 2001 Explorer Sportsman Concept Looks For a New Home
Verdad Gallardo
10 Best Ford Truck Engines We Miss the Most!
Joe Kucinski
Thread Starter
|
Fleet Mechanic
Joined: Dec 2005
Posts: 1,254
Likes: 120
Ya I am pretty excited to get these installed. It would be nice if I can get it all done tomorrow but we will see.
This will probably continue to pull me down the PMS road.....yikes.
- upgrade the intake
- larder exhaust
- bigger turbo
- hpop
- larger injectors.
- ect ect ect
please stop me.........
This will probably continue to pull me down the PMS road.....yikes.
- upgrade the intake
- larder exhaust
- bigger turbo
- hpop
- larger injectors.
- ect ect ect
please stop me.........
It's a Van Gogh
Joined: Feb 2010
Posts: 7,813
Likes: 1,335
From: Elk Grove, CA
Sadly I am fresh out of sacrificial goats. But I shall do my anti-rain dance anyway! 
Just finished loading the truck with tools and various spares. Oddly enough I found the little EGT probe "install kit" from Clay, but not my floor jack. Go figure.
Just finished loading the truck with tools and various spares. Oddly enough I found the little EGT probe "install kit" from Clay, but not my floor jack. Go figure.
