Opinions needed
 

Ok as a lot of you know I've been working on a graphic design for the side of my truck and I want your opinion on what I came up with. Please be honest and tell me what ya think..... here it is.

http://i7.photobucket.com/albums/y25...R/New6onbc.jpg

I think that is cool looking!

Nah doesn't fit IMO. Too much going on in one stripe. From bends to checkers to flames. K.I.S.S. You should know that means!

Thanks guys so far I'm really not sure on it. Ryan I dont know what K.I.S.S. is

K: Keep, I: It, S: Simple, S: Stupid.

just from what I know.

1st I am no expert, so I probably don't know what I am talking about.

It looks good Brian,But is there any way to make changes to it to make it your own design? Like maybe like make it come down off the hood,Or look like it is coming from the front fender well.

Like i said ,I don't know everything about this stuff. Just make it your design,not a generic set of graphics.

Just my 2 cents.

No expert here, but, for my taste, I would prefer it to be longer, more an element of the design, less involved and less of a focus. I think that you are really onto something, Brian, sometimes less is more.... One hundred people polled, and one hundred and one different opinions! Just make it yours alone.......

I think it would look good with it coming from the wheel well

Thanks for the input guys keep it coming, and Barry this is my own design in a way, I basically combined several different graphics to make one.....

The design on the door forward looks like what I just saw on a blazer.

Like the rest have stated, less would look better IMO. Then again I like your truck the way it is without anything. Always have, always will.:)

Are you going to use black?

I tryed several different ways to do the front, up on the hood I thought was to much with the flames on it. Out of the wheel well made so I had to go to low on the body I thought so I needed somewhere to start it at and if I went over the whole fender it made the need for more on the bed. Thanks for the input all

George I like it the way it is to but I'm wanting to spice it up some so to speak and as for the color I'm thinking like a burgandy color but I'm not possitive on that yet.

brian i will call u and we can chat... its been a while

I like it!
It starts with a burnout into a checkered flag, then a flame out...cool!

And keep in mind,,,it will look better without the white baking on it.So it will look smaller when installed.

Up to you Brian,,,truck looks good with or without.

Oh,,and I like the flames on the tail lights.

Thanks Phil, never relized the start looked like a burn out.

Ok I did some changing and have 2 options a little different than before

http://i210.photobucket.com/albums/b...05/New6bs2.jpg

http://i210.photobucket.com/albums/b...5/New6bs3a.jpg


What do ya's think?

i like the top design better in your last post, but i would go black instead of grey it would fit better, but at the end of the day you drive it not anyone else

I agree with coastie, the top one looks best.

The top one is more like it Brian!!!! You are getting the hang of that thing ain't ya......

I'm getting better all the time Barry..... I'm not sure which one I like better thought. Thanks for the input guys..

I like the bottom one. If you go with the top one, try to lower it a little, so you are not going over the handle. That would be a PIA to apply.

Thanks Kevin and I would definetly move it a bit to keep it off the handle.

Still not digging it. I say wait till you use paint and then do the flames.

I prefer the first longer one! Is is possible to fade it color-wise from dark(front fender) to lighter? Can you do a computer simulation to save you some work? Like George R. says, that's a nice looking truck...............even with nothin'!

Hey Brian, have you considered more of a lightning bolt style?

I dont have the stuff to do a fade however I've been thinking about making the graphic in peices so I could use multiple colors and what I'm doing is the best I can do without major work for a computor simulation. Thanks George


I was wanting to stay with the flames since I have them on my dash.

That makes sense Brian.

Here is a site that shows some design ideas and acutally has sample pics on trucks. http://www.customautotrim.com/graphics/truck/

Like these,,, Graphics Product

Just as examples

Thanks George I might be able to use some of that stuff

I looking for one for my Ranger that BD's Custom will do for me.:)

It's B&B Graphics is the name we've settled with. I'll do anything for a price :-hair well almost anything 8D

OK, thanks for the Update, lol

Brian, I like the top one as well.

Thanks Dave, I'm not sure yet but I am leaning to that one

Brian, like I said over in the chat thread, if you need that wleding done, let me know, Ill run down one day after work.

I do need to get that done Dave, we"ll get together real soon on that. Tuesdays are usually my best day, didn't you say you needed to weld something also.

I cant think of any thing I need welded. pertty much any time between no and thanksgiving is good for me, after thanksgiving Im going to be gone for a few weeks.

how about either tomorrow or the 18th which ever is better for you, after that I'll be layed up till around turkey day.

tommorrow will work for me, I acctually have the day off being that is Veterans day.

That would be sweet. Here's my addy so you can mapquest me

185 Chestnut Springs Rd
Chesapeake City MD 21915

I'm usually home between 3:30 and 3:45
If you need to call me to heres my cell # 302-593-2287

allright see you tommorrow after noon.

Cool see ya then