Go Back   Ford Truck Enthusiasts Forums > Diesel > 6.0L Power Stroke Diesel
Sign in using an external account
Register Forgot Password?


6.0L Power Stroke Diesel 2003 - 2007 F250, F350 pickup and F350+ Cab Chassis, 2003 - 2005 Excursion and 2003 - 2009 van SPONSORED BY:

Welcome to Ford-Trucks Forums!
Welcome to Ford-Trucks.com.

You are currently viewing our forums as a guest, which gives you limited access to view most discussions and access our other features. By joining our community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join the Ford-Trucks Forums community today!





 
Reply
 
LinkBack Thread Tools Search this Thread
  #1 (permalink)  
Old 03-02-2007, 03:42 PM
dieselfitter dieselfitter is offline
New User
 
Join Date: Apr 2005
Posts: 18
dieselfitter is starting off with a positive reputation.
Tsb 7-05-04 ?

Took truck to dealer (03 F350 6.0, 78k miles), for coolant leak and rough cold start. They fixed leak (EGR Cooler) and for the rough start they wrote "Found cylinder 2&5 eratic IC when cold. Performed TSB 7-05-04 Reprogram PCM." My question is is this the latest warming flash. Couldnt find info on this TSB. Could someone explain what this one is. Thank you. Wont know if it helped till I start it tommorow morning when its cold.
Mark
Reply With Quote
  #2 (permalink)  
Old 03-03-2007, 05:08 AM
satcom40's Avatar
satcom40 satcom40 is offline
Elder User
 
Join Date: Oct 2004
Location: Ct.
Posts: 577
satcom40 is starting off with a positive reputation.
Here is the TSB.
This article supersedes TSB 06-22-3 to update the Service Procedure. ISSUE: Some vehicles equipped with a 6.0L diesel engine may experience white smoke, lack of power, exhaust odor, surges, running rough, or no start when cold. These conditions are caused by the injector spool valve sticking internally during cold engine operation (engine oil temperature (EOT) less than 70 F ( 21 C)) . The concern is typically evident following a cold start after an overnight soak at ambient temperatures below 70 F (21 C). and may last 3-5 minutes or longer as the vehicle warms up. The concern completely disappears after driving and the EOT is greater than 150 F (66 C). This concern typically occurs on vehicles with greater than 15,000 miles (24,140 Km/h). ACTION: Diagnose and address any warm driveability issues or hard fault diagnostic trouble codes (DTCs) prior to performing this TSB. Then if cold driveability symptoms still exist use the following Service Procedure. SERVICE PROCEDURE This procedure includes a FICM calibration that adds inductive heating of the injector coils to locally heat the oil in the injector to normal operating temperatures very rapidly and keep it hot until normal overall engine oil temperature is achieved. This will prevent cold spool valve sticking on all injectors. Therefore, it will not be necessary to replace fuel injectors for the cold driveability symptoms listed in this TSB. Inductive heat is active in Key On Engine Run (KOER) mode below 2500 RPM. It is tapered out from 131-167 F (55-75 C) EOT, and is fully deactivated above 185 F (85 C) EOT.
*Printable View (70 KB) TSB 07-5-4  COLD START DRIVEABILITY - WHITE SMOKE, LACKS POWER, EXHAUST ODOR, SURGES, RUNS ROUGH, OR NO START - 6.0L Publication Date: February 27, 2007 FORD: 2003-2005 Excursion 2003-2007 F-Super Duty 2004-2007 E-350, E-450 NOTE: DO NOT USE CLICK TEST OR POWER BALANCE TO IDENTIFY COLD INJECTOR PERFORMANCE ISSUES, BECAUSE THE INDUCTIVE HEATING STRATEGY IS NOT ACTIVE DURING THESE TESTS. INJECTORS WHICH DO NOT RESPOND IN CLICK TEST OR POWER BALANCE WILL RESPOND IN NORMAL RUN MODE WITH THE INDUCTIVE HEAT CALIBRATION
This updated calibration strategy is a greater improvement than the previous post-cycle Fuel Injector Control Module (FICM) software release that cycled the injectors after shutdown (TSB 06-22-3). This strategy will eliminate the need to post-cycle the injector spool valves, and as a result will also eliminate the need to perform the E-Series wiring modification. The strategy achieves rapid heating of the oil in the injector through inductive heating of the injector coils. The Customer Information Sheet that was included with TSB 06-22-3 is no longer necessary. Customers who receive this new calibration after previously having received the post-cycle calibration (described in 06-22-3) will notice the buzzing noise at shutdown has been eliminated. This is normal, as the
NOTE: IF THE VEHICLE RUNS ROUGH OR HAS A MISFIRE WHEN THE ENGINE IS AT OPERATING TEMPERATURE, DIAGNOSE THOSE CONCERNS BEFORE PROCEEDING WITH THIS TSB.
post-cycle is no longer needed with inductive heating. Additionally, for E-Series there is no need to remove wiring modifications that were previously performed per TSB 06-22-3. Unmodified E-Series vehicles will NOT need the wiring modification with this calibration. 1. Using Module Reprogramming: FICM menu in IDS, reprogram the FICM to the latest calibration using IDS release 47.8 and higher or 48.2 and higher. This new calibration is not included in the VCM 2007.3 DVD. Calibration files may also be obtained at www.motorcraft.com. 2. If the customer previously had the Post Cycle calibration, notify them they will no longer hear the injector cycling after engine shutdown. WARRANTY STATUS: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage And Emissions Warranty Coverage IMPORTANT: Warranty coverage limits/policies are not altered by a TSB. Warranty coverage limits are determined by the identified causal part. DEALER CODING NOTE: The information in Technical Service Bulletins is intended for use by trained, professional technicians with the knowledge, tools, and equipment to do the job properly and safely. It informs these technicians of conditions that may occur on some vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by "do-it-yourselfers". Do not assume that a condition described affects your car or truck. Contact a Ford, Lincoln, or Mercury dealership to determine whether the Bulletin applies to your vehicle. Warranty Policy and Extended Service Plan documentation determine Warranty and/or Extended Service Plan coverage unless stated otherwise in the TSB article. The information in this Technical Service Bulletin (TSB) was current at the time of printing. Ford Motor Company reserves the right to supercede this information with updates. The most recent information is available through Ford Motor Company's on-line technical resources. Copyright 2007 Ford Motor Company OPERATION DESCRIPTION TIME 070504A 2003-2007 F-Super Duty, 2003-2005 Excursion, 2004-2007 Econoline 350/450 6.0L: Reprogram The Fuel Injector Control Module (FICM) (Do Not Use With 12650D, 12650D84) 0.7 Hr. BASIC PART NO. CONDITION CODE 9E527 42
__________________
04 F-250 SD 6.0L XLT EC SB Black, May 04 build. Bypass filter for Oil & Coolant, Remote start, Pre-Post Luber, Scan Gauge, 46 gal fuel tank, Boost & Pyro.
Reply With Quote
  #3 (permalink)  
Old 03-03-2007, 05:13 AM
Bushwhacker Bushwhacker is offline
Senior User
 
Join Date: Feb 2004
Location: NW Illinois
Posts: 305
Bushwhacker is starting off with a positive reputation.
Quote:
Originally Posted by satcom40
Here is the TSB.
This article supersedes TSB 06-22-3 to update the Service Procedure. ISSUE: Some vehicles equipped with a 6.0L diesel engine may experience white smoke, lack of power, exhaust odor, surges, running rough, or no start when cold. These conditions are caused by the injector spool valve sticking internally during cold engine operation (engine oil temperature (EOT) less than 70 F ( 21 C)) . The concern is typically evident following a cold start after an overnight soak at ambient temperatures below 70 F (21 C). and may last 3-5 minutes or longer as the vehicle warms up. The concern completely disappears after driving and the EOT is greater than 150 F (66 C). This concern typically occurs on vehicles with greater than 15,000 miles (24,140 Km/h). ACTION: Diagnose and address any warm driveability issues or hard fault diagnostic trouble codes (DTCs) prior to performing this TSB. Then if cold driveability symptoms still exist use the following Service Procedure. SERVICE PROCEDURE This procedure includes a FICM calibration that adds inductive heating of the injector coils to locally heat the oil in the injector to normal operating temperatures very rapidly and keep it hot until normal overall engine oil temperature is achieved. This will prevent cold spool valve sticking on all injectors. Therefore, it will not be necessary to replace fuel injectors for the cold driveability symptoms listed in this TSB. Inductive heat is active in Key On Engine Run (KOER) mode below 2500 RPM. It is tapered out from 131-167 F (55-75 C) EOT, and is fully deactivated above 185 F (85 C) EOT.
*Printable View (70 KB) TSB 07-5-4  COLD START DRIVEABILITY - WHITE SMOKE, LACKS POWER, EXHAUST ODOR, SURGES, RUNS ROUGH, OR NO START - 6.0L Publication Date: February 27, 2007 FORD: 2003-2005 Excursion 2003-2007 F-Super Duty 2004-2007 E-350, E-450 NOTE: DO NOT USE CLICK TEST OR POWER BALANCE TO IDENTIFY COLD INJECTOR PERFORMANCE ISSUES, BECAUSE THE INDUCTIVE HEATING STRATEGY IS NOT ACTIVE DURING THESE TESTS. INJECTORS WHICH DO NOT RESPOND IN CLICK TEST OR POWER BALANCE WILL RESPOND IN NORMAL RUN MODE WITH THE INDUCTIVE HEAT CALIBRATION
This updated calibration strategy is a greater improvement than the previous post-cycle Fuel Injector Control Module (FICM) software release that cycled the injectors after shutdown (TSB 06-22-3). This strategy will eliminate the need to post-cycle the injector spool valves, and as a result will also eliminate the need to perform the E-Series wiring modification. The strategy achieves rapid heating of the oil in the injector through inductive heating of the injector coils. The Customer Information Sheet that was included with TSB 06-22-3 is no longer necessary. Customers who receive this new calibration after previously having received the post-cycle calibration (described in 06-22-3) will notice the buzzing noise at shutdown has been eliminated. This is normal, as the
NOTE: IF THE VEHICLE RUNS ROUGH OR HAS A MISFIRE WHEN THE ENGINE IS AT OPERATING TEMPERATURE, DIAGNOSE THOSE CONCERNS BEFORE PROCEEDING WITH THIS TSB.
post-cycle is no longer needed with inductive heating. Additionally, for E-Series there is no need to remove wiring modifications that were previously performed per TSB 06-22-3. Unmodified E-Series vehicles will NOT need the wiring modification with this calibration. 1. Using Module Reprogramming: FICM menu in IDS, reprogram the FICM to the latest calibration using IDS release 47.8 and higher or 48.2 and higher. This new calibration is not included in the VCM 2007.3 DVD. Calibration files may also be obtained at www.motorcraft.com. 2. If the customer previously had the Post Cycle calibration, notify them they will no longer hear the injector cycling after engine shutdown. WARRANTY STATUS: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage And Emissions Warranty Coverage IMPORTANT: Warranty coverage limits/policies are not altered by a TSB. Warranty coverage limits are determined by the identified causal part. DEALER CODING NOTE: The information in Technical Service Bulletins is intended for use by trained, professional technicians with the knowledge, tools, and equipment to do the job properly and safely. It informs these technicians of conditions that may occur on some vehicles, or provides information that could assist in proper vehicle service. The procedures should not be performed by "do-it-yourselfers". Do not assume that a condition described affects your car or truck. Contact a Ford, Lincoln, or Mercury dealership to determine whether the Bulletin applies to your vehicle. Warranty Policy and Extended Service Plan documentation determine Warranty and/or Extended Service Plan coverage unless stated otherwise in the TSB article. The information in this Technical Service Bulletin (TSB) was current at the time of printing. Ford Motor Company reserves the right to supercede this information with updates. The most recent information is available through Ford Motor Company's on-line technical resources. Copyright 2007 Ford Motor Company OPERATION DESCRIPTION TIME 070504A 2003-2007 F-Super Duty, 2003-2005 Excursion, 2004-2007 Econoline 350/450 6.0L: Reprogram The Fuel Injector Control Module (FICM) (Do Not Use With 12650D, 12650D84) 0.7 Hr. BASIC PART NO. CONDITION CODE 9E527 42

When does this take effect. My dealership was not able to install this update yet.as of 2/28/07
__________________
2010 F-150 Lariat
Reply With Quote
  #4 (permalink)  
Old 03-03-2007, 11:49 AM
pstrang pstrang is offline
Senior User
 
Join Date: Jan 2004
Location: Idaho
Posts: 246
pstrang is starting off with a positive reputation.
Quote:
Originally Posted by Bushwhacker
When does this take effect. My dealership was not able to install this update yet.as of 2/28/07
Got mine yesterday, 3/2/07. Dealer said they had just gotten it that morning. I didn't think I had a problem before (had the buzz flash), but wow did it run smoother on start up this morning around 20F (and no more buzz on shutdown). Just like a summer day. Of course, I run synthetic oil too, so that helps.
__________________
2005-6L/PSD F-250 Lariat CC/SB/4x4:
- MBRP 4" turbo back, CCV4500, coolant bypass filter, oil bypass filter, X-monitor, Fluidampr, fuel x-over line, intake elbow, EGR cooler delete w/ welded uppipe, wrapped headers and turbo hot-side.
Reply With Quote
  #5 (permalink)  
Old 03-04-2007, 10:08 AM
Bushwhacker Bushwhacker is offline
Senior User
 
Join Date: Feb 2004
Location: NW Illinois
Posts: 305
Bushwhacker is starting off with a positive reputation.
I think I will check tomorrow to see if they have it available.
__________________
2010 F-150 Lariat
Reply With Quote
  #6 (permalink)  
Old 03-04-2007, 08:33 PM
dieselfitter dieselfitter is offline
New User
 
Join Date: Apr 2005
Posts: 18
dieselfitter is starting off with a positive reputation.
Thank you for the information, you guys are great! Cold start seems to be much smoother but it is also in the thirtys now. there is also still about a 3-5 second period of white smoke. Hopefully my average of 17MPG (Half highway, Half city driving) will stay the same. By the way dont get me wrong this is the best truck I have ever owned, I am all smiles everytime I fire this thing up!
Reply With Quote
  #7 (permalink)  
Old 03-05-2007, 10:29 AM
johnnysF350's Avatar
johnnysF350 johnnysF350 is offline
Elder User
 
Join Date: Dec 2006
Location: New Jersey
Posts: 594
johnnysF350 is starting off with a positive reputation.
Do you guys know if they will automatically do this flash at a regular service or do I have to be having a problem with cold starts to get it? I havent noticed a cold start issue on my '06 but most of it's cold starts are in a 55 degree garage.
__________________
2006 F-350 Lariat 6.0 PSD, Dark Stone, CC, LB, 20" Wheels, Rhino Liner, Extang Trifecta, Bone stock.
Reply With Quote
Old 03-05-2007, 10:29 AM
Reply

Go Back   Ford Truck Enthusiasts Forums > Diesel > 6.0L Power Stroke Diesel

Tags
2004, 2006, 60, buzz, control, duty, e450, f350, heat, inductive, injection, injectors, leak, module, strategypsd, super, tsb

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On
Forum Jump



All times are GMT -5. The time now is 03:08 AM.


Powered by vBulletin® Version 3.7.5
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Advertising - Terms of Use - Privacy Statement - Jobs
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. Ford is a registered trademark of the Ford Motor Company.

vbulletin Admin Backup