Cummins Conversion Build
#31
12-01-2010, 10:10 PM
Join Date: Dec 2003
Location: NW Arkansas
Posts: 2,392
Likes: 0
Received 0 Likes
on
0 Posts
Well I got some new parts in.
Lower End Gasket Kit
<a href="http://s916.photobucket.com/albums/ad9/jkidd_39/Cummins%20Conversion/?action=view&current=FumminsDec1025.jpg" target="_blank"><img src="http://i916.photobucket.com/albums/ad9/jkidd_39/Cummins%20Conversion/FumminsDec1025.jpg" border="0" alt="Photobucket"></a>
Getting ready to start tearing into the Cummins..
And apparently this in the only pic I can post.. I don't know what the hell is up tonight.. I'll try again in the morning.. Got a Fass 150, CFM+ intake horn and new main bearings for the VP44 Rod swap...
Lower End Gasket Kit
<a href="http://s916.photobucket.com/albums/ad9/jkidd_39/Cummins%20Conversion/?action=view&current=FumminsDec1025.jpg" target="_blank"><img src="http://i916.photobucket.com/albums/ad9/jkidd_39/Cummins%20Conversion/FumminsDec1025.jpg" border="0" alt="Photobucket"></a>
Getting ready to start tearing into the Cummins..
And apparently this in the only pic I can post.. I don't know what the hell is up tonight.. I'll try again in the morning.. Got a Fass 150, CFM+ intake horn and new main bearings for the VP44 Rod swap...
#32
12-01-2010, 10:13 PM
Join Date: Dec 2003
Location: NW Arkansas
Posts: 2,392
Likes: 0
Received 0 Likes
on
0 Posts
Main Bearings for the VP44 Rod swap
<a href="http://s916.photobucket.com/albums/ad9/jkidd_39/Cummins%20Conversion/?action=view&current=FumminsDec1026.jpg" target="_blank"><img src="http://i916.photobucket.com/albums/ad9/jkidd_39/Cummins%20Conversion/FumminsDec1026.jpg" border="0" alt="Photobucket"></a>
<a href="http://s916.photobucket.com/albums/ad9/jkidd_39/Cummins%20Conversion/?action=view&current=FumminsDec1026.jpg" target="_blank"><img src="http://i916.photobucket.com/albums/ad9/jkidd_39/Cummins%20Conversion/FumminsDec1026.jpg" border="0" alt="Photobucket"></a>
#34
12-04-2010, 10:57 AM
And your putting this much moola into it, you could always just make it a shortbed
#35
12-04-2010, 12:04 PM
Join Date: Dec 2003
Location: NW Arkansas
Posts: 2,392
Likes: 0
Received 0 Likes
on
0 Posts
Everyone is more than welcome to come take a look! All I gotta pull is the tranny and she is ready. I will hopefully be starting the cummins disassembly soon enough. The injectors need to go out and the rods will go out for shotpeening and cryo. The Pistons will be ceramic coated on top and teflon coating on the sideskirts.
#39
12-04-2010, 04:01 PM
Join Date: Dec 2003
Location: NW Arkansas
Posts: 2,392
Likes: 0
Received 0 Likes
on
0 Posts
I am not sure on the color yet. I think the block will be cummins beige. I haven't made a decision on the engine cover. I think I am gonna just machine a plate and do a custom design.. or maybe the King Ranch "W"
#40
12-04-2010, 04:32 PM
Postmaster
Join Date: May 2008
Location: horicon Wi
Posts: 3,099
Likes: 0
Received 0 Likes
on
0 Posts
#42
12-05-2010, 12:50 PM
Join Date: Feb 2004
Location: IOWA
Posts: 2,365
Likes: 0
Received 0 Likes
on
0 Posts
There was a guy on PSN that put an International DT360 in his truck. Supposedly in stock form they are good to well over 1000hp.I know a lot of guys that run them in pulling tractors running that kind of hp, don't know if they're completely stock.
#43
12-05-2010, 01:51 PM
Join Date: Feb 2005
Location: Oregon
Posts: 1,319
Likes: 0
Received 0 Likes
on
0 Posts
#44
12-05-2010, 02:29 PM
Postmaster
Join Date: May 2008
Location: horicon Wi
Posts: 3,099
Likes: 0
Received 0 Likes
on
0 Posts
#45
12-05-2010, 07:54 PM
Join Date: Feb 2005
Location: Oregon
Posts: 1,319
Likes: 0
Received 0 Likes
on
0 Posts