Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: chriscris
Showing results 1 to 15 of 344
Search took 0.32 seconds.
07-19-2019, 07:11 AM
Replies: 12
Views: 644
Posted By chriscris

Crank hole and rad drain. The seal goes toward...

Crank hole and rad drain. The seal goes toward the radiator and it bolts to the rear edge of the part below the grille and to the inner fenders.
It is on an angle when in place
07-18-2019, 07:16 AM
Replies: 842
Views: 263,383
Posted By chriscris

1948 F47 completely restored for sale

Just finished complete restoration. Runs and drives perfectly. Located near Milton, Ontario, Canada
$39k USD


Complete info here...
06-17-2019, 07:44 PM
Replies: 33
Views: 2,186
Posted By chriscris

pm has been sent

pm has been sent
06-16-2019, 04:59 PM
Replies: 33
Views: 2,186
Posted By chriscris

Yes.

This is leftover.
Give me a day or 2 to find out shipping (from Ontario, Canada)
06-14-2019, 07:15 PM
Replies: 33
Views: 2,186
Posted By chriscris

A quick blast, and a lick of paint....... ...

A quick blast, and a lick of paint.......

https://cimg2.ibsrv.net/gimg/www.ford-trucks.com-vbulletin/864x1152/20190614_090437_resized_4cbcce71fe9709805579a615c35a7488fcb80bd2.jpg
06-13-2019, 07:00 PM
Replies: 33
Views: 2,186
Posted By chriscris

This? ...

This?

https://cimg0.ibsrv.net/gimg/www.ford-trucks.com-vbulletin/864x1152/bracket_1__8d9ec525357eb711d8f2e66149aed45bb7df122f.jpg...
06-12-2019, 06:42 PM
Replies: 33
Views: 2,186
Posted By chriscris

My post above....

....sorry. never mind
06-11-2019, 07:06 AM
Replies: 33
Views: 2,186
Posted By chriscris

not sure if this helps; ...

not sure if this helps;

https://www.ford-trucks.com/forums/915923-51-e-brake-parts.html

Let me know what you may need. Mine is done, so I can let the spares go now.
05-23-2019, 01:47 PM
Replies: 13
Views: 1,036
Posted By chriscris

I used POR engine paint, (mainly because it was...

I used POR engine paint, (mainly because it was the only Ford blue I had in stock) and it is bulletproof.
A tiny brush, some POR thinner for better flow, and a giant magnifying glass.
05-23-2019, 07:16 AM
Replies: 5
Views: 630
Posted By chriscris

I have a few extra double filament sockets that...

I have a few extra double filament sockets that press right in after you press out the single ones.
Then just use an 1157A (A for amber) bulb. The yellow aftermarket lenses look poopy.
Easy Peezy
05-22-2019, 06:05 PM
Replies: 1
Views: 244
Posted By chriscris

Aftermarket flathead temperature sender opinions

Is there any experience with the aftermarket temperature sending units available?
I am in the market for both and don't mind going NOS, would still like any opinions.
Thanks

Chris
05-22-2019, 09:01 AM
Replies: 7
Views: 716
Posted By chriscris

Is the coil burnt? An original horn can be...

Is the coil burnt?
An original horn can be opened up and generally the points need cleaning.
04-16-2019, 10:38 AM
Replies: 13
Views: 474
Posted By chriscris

Exactly correct. The case can also be worn to the...

Exactly correct. The case can also be worn to the point of scrap. Without inspection, $50-$100 would be expected. If it were inspected, with good gears, bearings, seals, synchro's and no case wear, I...
04-08-2019, 12:55 PM
Replies: 2
Views: 326
Posted By chriscris

I grabbed a set off eBay for 150 and they are way...

I grabbed a set off eBay for 150 and they are way better than expected, but I imagine they all come from the same place.
The universal clips I did not use, so they are available if needed.
04-08-2019, 12:52 PM
Replies: 7
Views: 645
Posted By chriscris

Northern Classic Trucks were doing it, but have...

Northern Classic Trucks were doing it, but have since retired, Haven't heard who may have bought up the dies or inventory.
Showing results 1 to 15 of 344
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.