Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: x_man586
Showing results 1 to 15 of 168
Search took 0.31 seconds.
Replies: 43
Views: 4,707
Posted By x_man586

That's cool. I am going to figure out how the...

That's cool. I am going to figure out how the truck does it now. Then install the valve so that it works the same way.
Replies: 43
Views: 4,707
Posted By x_man586

Well originally my truck was E.F.I. I was going...

Well originally my truck was E.F.I. I was going to look at the diagrams in my manual and use a test light to see what was what anyway. To check what I had against their schematics. I wasn't going to...
Replies: 43
Views: 4,707
Posted By x_man586

I bought the valve yesterday and have been...

I bought the valve yesterday and have been looking at the schematics. I know the valve was engineered a certain way and if I follow their wiring diagram it will work. However if the purpose of the...
Replies: 43
Views: 4,707
Posted By x_man586

Do you have the part number for the valve? This...

Do you have the part number for the valve? This is something I need to do. Mine is allowing the rear tank to overfill the front.
Replies: 11
Views: 340
Posted By x_man586

That is good to know.

That is good to know.
Replies: 11
Views: 340
Posted By x_man586

you are correct in that the only way to know your...

you are correct in that the only way to know your timing is perfect is for the engine to be running, but since I couldn't get it running I figured spinning over fast would be close. I do it that was...
Replies: 11
Views: 340
Posted By x_man586

Maybe I got all of the complicated stuff right...

Maybe I got all of the complicated stuff right and screwed up the easy part.
Replies: 11
Views: 340
Posted By x_man586

it is not running at all, but spinning the motor...

it is not running at all, but spinning the motor the light shows fire at 10*. I didn't check to see what stroke it was on. I guess I have gotten lucky the past few times by turning the crank till 0*...
Replies: 11
Views: 340
Posted By x_man586

Problems after dizzy adjustment.

I had problems with detonation after a dsII swap. I decided to install an adjustable vacuum regulator kit from Crane cams because without the vacuum attached it ran fine. It ran before, but after I...
Replies: 5
Views: 1,066
Posted By x_man586

Even if I am 99% sure I know the answer I will...

Even if I am 99% sure I know the answer I will still ask the question because I might learn something new
Replies: 5
Views: 1,066
Posted By x_man586

I meant if there was something in the front...

I meant if there was something in the front suspension that has been known to wear out on a more than regular basis. For example some cars have problems with the spring perches. I know springs don't...
Replies: 5
Views: 1,066
Posted By x_man586

Bad coil spring? Passenger side sits lower than driver's side.

I'm guessing spring, but it could be something else. Is there a common failure point in the front suspension? I am not familiar with ttb.
Replies: 137
Views: 18,616
Posted By x_man586

Nice job!!!

Nice job!!!
Replies: 8
Views: 997
Posted By x_man586

Thanks guys. I will be patient and careful. I...

Thanks guys. I will be patient and careful. I work on other people's cars everyday. I will pretend it is one of their cars.
Replies: 5
Views: 476
Posted By x_man586

This is how I have it now, pardon the rust ...

This is how I have it now, pardon the rust
http://img845.imageshack.us/img845/2756/8pc5.jpg
Showing results 1 to 15 of 168
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.