Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: Xcursion88
Showing results 1 to 15 of 223
Search took 0.20 seconds.
06-14-2019, 03:52 PM
Replies: 6
Views: 1,068
Posted By Xcursion88

They don't even affect the spray whatsoever... ...

They don't even affect the spray whatsoever...

Moreover the o rings do the sealing.

I'm thinking potentially they could be there to reduce noise.

I've found some out of China. But delivery...
06-14-2019, 12:39 PM
Replies: 6
Views: 1,068
Posted By Xcursion88

I guess I needed to be more clear. I know...

I guess I needed to be more clear.

I know these are injectors. I thought I implied that fairly well...

Anyways the thing on the very end. Not the o rings...the pintle cap type thing but it's...
Forum: Engine Swaps
04-03-2019, 01:03 AM
Replies: 1
Views: 502
Posted By Xcursion88

Help picking the engine

Swapping a SBF into a Jeep TJ
4.10 gears

Two choices are a 2000 5.0 out of a mountaineer
And a 1996 351 out of F150
Both are OBD2

Using a T18 or Np435. I may or may not use a 205 behind...
09-08-2017, 11:35 AM
Replies: 12
Views: 3,679
Posted By Xcursion88

Reason being is that when one goes bad the other...

Reason being is that when one goes bad the other is not far behind. Unless you did something specifically to ruin a specific caliper.... In other words if the caliper has gone bad just through age...
09-08-2017, 04:28 AM
Replies: 36
Views: 5,733
Posted By Xcursion88

x codes. What you are trying to accomplish the x...

x codes. What you are trying to accomplish the x code will get you the desired ride you want.
on the lift aspect...how much lift the x code provides varies based on your current state of the...
08-26-2017, 11:23 AM
Replies: 48
Views: 29,851
Posted By Xcursion88

Relax yourself sir... I had thought I read...

Relax yourself sir...

I had thought I read somewhere in this thread somebody has started chiming in about the other super duty trucks within the lineup. I went back realized I was looking at two...
08-25-2017, 11:20 PM
Replies: 48
Views: 29,851
Posted By Xcursion88

I didn't mean 180 in direction. You said the...

I didn't mean 180 in direction. You said the double carden NEEDS angle help and while any shim or block to try to get point A to point B on as straight of a plane as possible is always a good thing...
08-25-2017, 09:54 PM
Replies: 48
Views: 29,851
Posted By Xcursion88

You have that 180 degrees opposite. The...

You have that 180 degrees opposite.

The double carden doesn't need an angle...but rather it's used to help over come the ill effects of steep driveline angles.
07-31-2017, 01:37 AM
Replies: 34
Views: 8,362
Posted By Xcursion88

Aaaahhhh Mr 18,000 posts. How many of...

Aaaahhhh
Mr 18,000 posts.

How many of those 18,000 are actually a contribution to the thread? I count two today that has absolutely nothing to help.with the thread.

almost all of your posts...
07-30-2017, 04:08 PM
Replies: 20
Views: 19,344
Posted By Xcursion88

Laughable. Ridiculously laughable. You...

Laughable.

Ridiculously laughable.
You mean the Chink made spicer u joints?
I'll take USA made skf u joints all day long. The top shelf Napa u joints are skf. Plenty strong. Greasable. Lay...
07-30-2017, 02:07 PM
Replies: 20
Views: 19,344
Posted By Xcursion88

Take hub bolts off as you said warn. Do snap...

Take hub bolts off as you said warn.
Do snap ring and washers.
Take off caliper bracket bolts. 21mm I believe.
That way you leave the caliper loaded.
Rotor off.
Four bolts on back of wheel...
07-30-2017, 01:20 PM
Replies: 20
Views: 19,344
Posted By Xcursion88

No thanks needed...abd you're welcome. ...

No thanks needed...abd you're welcome.

Seals...well only if you mess them up.

Had you just replaced a u joint not long ago?

I can't stress to you enough the importance of NOT using the...
07-30-2017, 01:09 PM
Replies: 20
Views: 19,344
Posted By Xcursion88

There will be some movement. You have a bearing...

There will be some movement. You have a bearing inside the tube at the pumpkin.

Then nothing all the way out until the axle stub shaft goes into the wheel bearing hub.

Way too far between...
07-30-2017, 12:48 PM
Replies: 20
Views: 19,344
Posted By Xcursion88

I can't see your videos for some reason. If...

I can't see your videos for some reason.

If you mean the axle shafts appear to be moving inward toward the pumpkin
These axles are not held in by c clips inside the pumpkin.

Everything you...
07-30-2017, 12:33 PM
Replies: 15
Views: 12,124
Posted By Xcursion88

I've seen lots of pitman arms get sloppy. Age,...

I've seen lots of pitman arms get sloppy. Age, abuse, whatever.
In the engineering process there needs to be something that wears.
Example..if they made the pitman arm as hard as the output shaft...
Showing results 1 to 15 of 223
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.