Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: xdevdogx
Showing results 1 to 15 of 41
Search took 0.26 seconds.
11-13-2012, 07:47 PM
Replies: 7
Views: 2,740
Posted By xdevdogx

The harness looks like it has an inline blade...

The harness looks like it has an inline blade fuse taped to it. Has a tag on it that says it contains an unserviceable fuse and if its blown to replace with harness number blah blah blah. If this...
11-13-2012, 03:45 PM
Replies: 7
Views: 2,740
Posted By xdevdogx

Checked all the wiring last night from vss...

Checked all the wiring last night from vss forward, all looked good. Thought it might be the trailer wiring since I have two, one in the bed and one at the hitch, nope all is good there too. I'll...
11-13-2012, 02:08 PM
Replies: 7
Views: 2,740
Posted By xdevdogx

Thanks, but the rabs link in that post is no...

Thanks, but the rabs link in that post is no longer available. My rear brakes are fine condition and adjusted properly. Since this is the first time the rabs activated, my thought is that it is a...
11-13-2012, 01:36 PM
Replies: 7
Views: 2,740
Posted By xdevdogx

RABS blowing #13 fuse

My rabs activated last night for the first time ever on the ice, and it blew the #13 fuse. Put a new one in, and as soon as I hit the brakes again, this time, no rabs activated as far as I could tell...
11-13-2012, 01:21 PM
Replies: 24
Views: 117,435
Posted By xdevdogx

I've got the same issue, except mine is when the...

I've got the same issue, except mine is when the rabs kicks in. It blows the #13 fuse and then no brake lights and shift interlock occurs. I took out the other rabs 30 amp fuse just to quit blowing...
03-22-2012, 09:38 PM
Replies: 20
Views: 5,304
Posted By xdevdogx

The way I do a sea foam treatment is pour half in...

The way I do a sea foam treatment is pour half in the tank and then find a vacuum line that is common to all cylinders, center of the intake is best. Put the vacuum hose in the can and pinch it as...
03-20-2012, 02:37 PM
Replies: 22
Views: 869
Posted By xdevdogx

Make sure you get the fittings on nice and tight,...

Make sure you get the fittings on nice and tight, and hope that you dont get a leak, inside or outside. That will ruin your day in a hurry.
03-20-2012, 02:34 PM
Replies: 22
Views: 869
Posted By xdevdogx

Did you end up going with a mechanical oil...

Did you end up going with a mechanical oil pressure gauge?
03-20-2012, 02:19 PM
Replies: 22
Views: 869
Posted By xdevdogx

what kind of gauges did you get? I just installed...

what kind of gauges did you get? I just installed 4 on the A pillar, tach, water temp, oil pressure and trans temp. I plan on getting more temp sensors and installing them in the diff's and transfer...
03-20-2012, 02:13 PM
Replies: 22
Views: 869
Posted By xdevdogx

The switch is on the block by the firewall, just...

The switch is on the block by the firewall, just slightly off center towards the passenger side.
03-20-2012, 02:06 PM
Replies: 22
Views: 869
Posted By xdevdogx

Factory gauges are nothing more than an idiot...

Factory gauges are nothing more than an idiot light with a needle. Could be either the gauge or the switch. Try this to check which one it could be:

With the key in RUN and the engine off,...
03-13-2012, 08:24 AM
Replies: 4
Views: 623
Posted By xdevdogx

Thanks 7DF250, that is a sweet kit. I'm going to...

Thanks 7DF250, that is a sweet kit. I'm going to go with that for sure. Do you know of where I can find a list of all the codes and spring rates for the superduty springs? I dont want anything too...
03-12-2012, 02:55 PM
Replies: 4
Views: 623
Posted By xdevdogx

I used to work at that place and quite frankly,...

I used to work at that place and quite frankly, they are the kmart of anything offroad. About the only thing they are good for is purchasing the kits and doing it your self but there are so many...
03-12-2012, 10:13 AM
Replies: 4
Views: 623
Posted By xdevdogx

97 F350 460 spring conversion

I thought I read this somewhere on here, but I cant remember and search isn't helping. For the SD spring codes, isn't it X in the front and B for the rear, and from a 99 and up? I'm looking to level...
03-08-2012, 03:32 PM
Replies: 15
Views: 5,055
Posted By xdevdogx

As jas pointed out, it's hard to say without...

As jas pointed out, it's hard to say without hearing it. I would put money on either main bearings and or a wrist pin if it's more of a hollow sounding knock. If it seems to be more higher pitch then...
Showing results 1 to 15 of 41
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.