Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: mkoch96
Showing results 1 to 15 of 92
Search took 0.21 seconds.
06-02-2015, 05:59 PM
Replies: 19
Views: 1,723
Posted By mkoch96

If timelines work out, whenever I actually pull...

If timelines work out, whenever I actually pull the trigger on my cv swap, I will have a pair of 302 perches up for grabs. I just can make no promises right now about when exactly time and finances...
01-13-2015, 08:41 PM
Replies: 10
Views: 620
Posted By mkoch96

Am I wrong, or wouldn't that simply be a .030...

Am I wrong, or wouldn't that simply be a .030 over version of the Mercury 410? If so, that was supposedly a pretty good running combo.
01-04-2015, 09:51 AM
Replies: 27
Views: 10,144
Posted By mkoch96

The 1989-1997 Thunderbird Super Coupes had the...

The 1989-1997 Thunderbird Super Coupes had the correct Trac-Loc unit for the IRS also. If my research is correct, all manual transmission cars had Trac-Loc, and the automatic cars had them up to...
07-27-2014, 08:21 PM
Replies: 12
Views: 1,131
Posted By mkoch96

With as common as it is for these floats to sink,...

With as common as it is for these floats to sink, after 42 years it is very possible that you have 2 bad floats. Do like Binkowski said and ground the wire on each sender and see if the gauge goes...
05-21-2014, 12:32 PM
Replies: 14
Views: 4,623
Posted By mkoch96

I dont know the dimensions of the Mustang...

I dont know the dimensions of the Mustang K-member, but the big fabrication challenge would be building strut towers. That's the allure of the CV suspension. It is all self contained.
04-07-2014, 11:22 AM
Replies: 24
Views: 1,342
Posted By mkoch96

With all that you are doing to the engine, why...

With all that you are doing to the engine, why the ported stock intake? Are you going for the exterior appearance of a stock engine? An aluminum intake is usually one of the first mods on anyone's...
03-06-2014, 10:28 PM
Replies: 17
Views: 960
Posted By mkoch96

If you wind up needing that special driver for...

If you wind up needing that special driver for the secondary plate screws, it is called a "clutch" tip. Unfortunately, I don't remember what size it is off the top of my head. Sometimes they do...
03-04-2014, 06:36 PM
Replies: 9
Views: 584
Posted By mkoch96

I would think that the most straightforward...

I would think that the most straightforward junkyard swap in your case would be to find a 96 or older f150/250 with a 300,302, or 351w and a m5r2 5 speed. They have a hydraulic release bearing, but...
03-04-2014, 06:12 PM
Replies: 77
Views: 4,733
Posted By mkoch96

Lol, I used to do something similar in a Cougar...

Lol, I used to do something similar in a Cougar that I had with a digital dash. Wind it up to about 80, then push the button for km/h. You should see the look on her face when she glances over and...
02-20-2014, 10:02 AM
Replies: 10
Views: 1,005
Posted By mkoch96

I think when the OP said he needed to change the...

I think when the OP said he needed to change the pinion gear, he was referring to the driven speedometer gear, not the ring and pinion gears in the rear end. Technically, it is also a pinion gear,...
01-30-2014, 06:36 PM
Replies: 19
Views: 1,285
Posted By mkoch96

Yeah, that's how it works. I think the AN size...

Yeah, that's how it works. I think the AN size refers to the I.D. of the hose. Like AN-4 would be 1/4" hose. The ends are a tapered fitting so they seal well against pressure. We use them for...
01-30-2014, 09:43 AM
Replies: 19
Views: 1,285
Posted By mkoch96

Or you could do like we do in the race car world...

Or you could do like we do in the race car world and use an AN-4 braided steel line. They even make them with a kevlar coating on them now so they won't scuff up any paint that they happen to rub on...
01-30-2014, 09:12 AM
Replies: 18
Views: 1,150
Posted By mkoch96

Obviously any quality driveline shop knows this,...

Obviously any quality driveline shop knows this, but what you have to watch when changing tubing size and length is the critical speed. It is a function of the weld-to-weld length of the tubing and...
01-28-2014, 02:11 PM
Replies: 571
Views: 243,539
Posted By mkoch96

That's right. The 4bt was in a lot of bread...

That's right. The 4bt was in a lot of bread trucks and those little cab over trucks. I think Isuzu had their own 4 cylinder diesel also but I could be wrong on that one. The 6bt is the 6 cylinder...
01-27-2014, 10:12 AM
Replies: 18
Views: 1,150
Posted By mkoch96

You don't actually need that 4 bolt flange. My...

You don't actually need that 4 bolt flange. My '70 doesn't have it. It just has the yoke on the transmission like what I assume you already have.
Showing results 1 to 15 of 92
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.