Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: Outlaw56
Showing results 1 to 15 of 476
Search took 0.49 seconds.
08-20-2018, 01:44 PM
Replies: 9
Views: 379
Posted By Outlaw56

Raytech, can you explain what you mean by "full...

Raytech, can you explain what you mean by "full floater"? I like your idea of off road market.
08-20-2018, 01:43 PM
Replies: 9
Views: 379
Posted By Outlaw56

I have stored it for about 10 years, but I have...

I have stored it for about 10 years, but I have not offered it for free. I'm running out of room to store this stuff, manual transmissions, bell housing, fuel tanks, ugh.
08-20-2018, 12:55 PM
Replies: 9
Views: 379
Posted By Outlaw56

I think you may be right Abe. I'm considering...

I think you may be right Abe. I'm considering removing the new parts I installed and scrapping the axel and housing. That would probably get me more than I'm asking for the axel as is. I just don't...
08-19-2018, 12:58 PM
Replies: 9
Views: 379
Posted By Outlaw56

Good advise. I was not attempting to sell here...

Good advise. I was not attempting to sell here because of the high shipping costs. Once I get an idea what to ask, I was going to list on face book with the gear ratio, bolt pattern and photos. I'm...
08-18-2018, 02:56 PM
Replies: 9
Views: 379
Posted By Outlaw56

1956 Ford 250 Rear Axel.

I bought a 1956 F-250 Farm truck. I rebuilt both outsides of the axel (drums, brake shoes and all the parts that go with it). Its painted satin black and looks nice. I did not do anything to the...
03-16-2018, 11:18 AM
Replies: 16
Views: 796
Posted By Outlaw56

Repacing flat glass panels

When it comes to replacing flat glass panels, has anyone taken stock glass (flat only) to a local glass shop and had them make a duplicate that installed successfully? I can purchase side glass and...
10-25-2017, 10:55 AM
Replies: 95
Views: 31,529
Posted By Outlaw56

Unfortunately, No. I had a bad year. Lost two of...

Unfortunately, No. I had a bad year. Lost two of my best friends in the world, Megan and Chloe. They were King Charles Spaniels. Put me in a downer and really zapped my enthusiasm. Ended up getting a...
04-18-2017, 09:10 AM
Replies: 25
Views: 1,094
Posted By Outlaw56

I'm thinking thread size on a standard 5/16...

I'm thinking thread size on a standard 5/16 inverted flare is 24?
04-10-2017, 09:57 AM
Replies: 44
Views: 2,417
Posted By Outlaw56

John, did you attach a photo to your response? I...

John, did you attach a photo to your response? I am not seeing it. Its like it pops up for just a second and then disappears. I'm guessing you used disk brakes on the rear? My issue is the same set...
04-09-2017, 06:18 PM
Replies: 44
Views: 2,417
Posted By Outlaw56

After more digging, I realized the donar 9" Ford...

After more digging, I realized the donar 9" Ford truck axel I am swapping to my 56 F-100 had a 1/4" brake tube, but was reduced to 3/16" at the backing plate. So, with that discovery, I am going to...
04-09-2017, 11:24 AM
Replies: 7
Views: 429
Posted By Outlaw56

Stock Brake cylinder photo

Does anyone have a good photos to share of the stock brake master cylinder with attached brake lines and switch on a stock 56 F series Ford truck they can share?
04-02-2017, 09:50 AM
Replies: 18
Views: 1,177
Posted By Outlaw56

turnjr, Mid Fifty sells the ABS panels.

turnjr, Mid Fifty sells the ABS panels.
04-02-2017, 09:50 AM
Replies: 18
Views: 1,177
Posted By Outlaw56

That's awesome tech tips. I'm happy to know if I...

That's awesome tech tips. I'm happy to know if I break the clips there is a really good option and with better more reliability. I have three of these trucks I'm working on. Two are going together...
04-01-2017, 09:50 PM
Replies: 18
Views: 995
Posted By Outlaw56

F-1. Cutting the cab loose like you did is not...

F-1. Cutting the cab loose like you did is not good, however, it is not catastrophic until you weld in the firewall and floor boards. You need to find an original cab to take measurements from and...
04-01-2017, 09:53 AM
Replies: 18
Views: 995
Posted By Outlaw56

By the time you pay someone to do the welding,...

By the time you pay someone to do the welding, you could have purchased a nice small mig welder capable of handling sheet metal. I would recommend a welder that will go to 1/4 inch metal. A little...
Showing results 1 to 15 of 476
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.