Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: MustModifyNow
Showing results 1 to 15 of 29
Search took 0.52 seconds.
Forum: 6.2L V8
01-19-2013, 03:08 PM
Replies: 67
Views: 58,067
Posted By MustModifyNow

How about a 4 inch stroke 4 inch bore motor from...

How about a 4 inch stroke 4 inch bore motor from the factory
Instead that would help help the low end torque
Forum: 6.2L V8
09-30-2011, 06:51 PM
Replies: 126
Views: 241,515
Posted By MustModifyNow

Not that 1 truck sell will make or break Ford,...

Not that 1 truck sell will make or break Ford, but I hope there are Ford engineers on here that read these posts.

If Ford will ecoboost the 6.2 liter (single or twin turbo) in the F250, I will go...
08-18-2009, 10:06 AM
Replies: 16
Views: 1,521
Posted By MustModifyNow

pulling at trailer with a super charger

Okay I will think about the gears. When I ordered this truck, I thought I ordered it with a limited slip rear end but when I got it, it was a one tire frier. My brother in law is a Ford truck...
08-17-2009, 05:25 PM
Replies: 16
Views: 1,521
Posted By MustModifyNow

pulling a trailer with a super charger

I have thought about a gear change but the way I see it is why if I'm not going to pull in over drive? At 65 mph it's turning 2500 rpms. With 4.30 gears in over drive it's probably turning 2200...
08-17-2009, 03:54 PM
Replies: 16
Views: 1,521
Posted By MustModifyNow

Pulling a trailer with a super charger

Okay good to know. Both of these brands would be fine. It would be nice to get a bit better mph (7-8 normally. Maybe 9 if I don't lead foot it) I'm not expecting any better. I have 3.73 gears,...
08-17-2009, 01:16 PM
Replies: 16
Views: 1,521
Posted By MustModifyNow

Pulling a trailer with a super charger

I'm sure there is a thread about this here somewhere but I could not find it. I see there are a few guys with super chargers on here, I am real curious about super chargers and how they perform...
02-09-2009, 03:05 PM
Replies: 28
Views: 1,338
Posted By MustModifyNow

I love my V-10 but you are missing the point on...

I love my V-10 but you are missing the point on why dealers never stocked the V-10 vs diesels and especially the 6 liter diesel. So if you are a business man, what price point do you want to push if...
02-09-2009, 02:47 PM
Replies: 37
Views: 31,764
Posted By MustModifyNow

my brother in law just installed a set of Banks...

my brother in law just installed a set of Banks headers on my 01 this past weekend and I had the Banks cat back muffler and tail pipe already. The cat back by itself made a nice throaty tone that...
12-04-2008, 03:09 PM
Replies: 9
Views: 12,384
Posted By MustModifyNow

He didn't have to trim the skirts there is a...

He didn't have to trim the skirts there is a little balancing patch (area to take material off when balacning) that is on either side of the piston pin boss. He had to take material off there. it...
12-04-2008, 02:55 PM
Replies: 9
Views: 12,384
Posted By MustModifyNow

my brother in law (young kid, Ford pickup...

my brother in law (young kid, Ford pickup mechanic) just picked up a 87 ranger and reworked his 2.9 and is about ready to fire it up so I will have to keep you posted on how it worked out. He put...
06-03-2008, 11:59 AM
Replies: 8
Views: 716
Posted By MustModifyNow

Only an observation from reading this website but...

Only an observation from reading this website but unless you buy the Banks headers, it appears everyone looses what bottom end out V-10's have with short headers. I have a 2001 V-10 and I just...
06-03-2008, 11:51 AM
Replies: 10
Views: 578
Posted By MustModifyNow

I had a plug let go at 100,000 miles. After...

I had a plug let go at 100,000 miles. After reading this website it appears some have the problem, and some don't but to me the problem seems to be worse if you are pulling heavy loads. I didn't...
05-29-2008, 12:31 PM
Replies: 52
Views: 54,236
Posted By MustModifyNow

Wylecoyote, if you find part numbers for the...

Wylecoyote, if you find part numbers for the turbo setup on the V-10 powered generators, I can get costs on the parts. My brother in law works at a Ford truck dealership and they do buy industrial...
02-18-2008, 06:49 PM
Replies: 127
Views: 8,763
Posted By MustModifyNow

I see you have some ported heads on the old...

I see you have some ported heads on the old T-bird, NPI, how do they do?
02-18-2008, 06:35 PM
Replies: 127
Views: 8,763
Posted By MustModifyNow

Why not just port the 2 valve heads? I would...

Why not just port the 2 valve heads? I would think that any shop that has CNC programs for the 2 valve 4.6 and 5.4 could certainly port the 2 valve V-10 heads and make the flow just as good or...
Showing results 1 to 15 of 29
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.