Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: vjsimone
Showing results 1 to 15 of 500
Search took 0.21 seconds.
07-05-2019, 03:39 PM
Replies: 7
Views: 521
Posted By vjsimone

Start it up from cold, if it goes to about a...

Start it up from cold, if it goes to about a 12-1500 rpm idle, before it settles back down, that's good.

Roll down the windows, make sure they work, leave them down while you listen for noises.
...
Replies: 4
Views: 557
Posted By vjsimone

I recommend you add some ISO HEET to mitigate the...

I recommend you add some ISO HEET to mitigate the effects of the old ethanol fuel now in your tank/s.
...
07-01-2019, 10:00 AM
Replies: 17
Views: 934
Posted By vjsimone

I took a look at that link above, probably not a...

I took a look at that link above, probably not a complete test.

Check this one; Fuel Injection Technical Library EGR Valve Position sensor (EVP) (http://www.fuelinjectedford.com/page35.html)
...
07-01-2019, 09:12 AM
Replies: 17
Views: 934
Posted By vjsimone

TAD & TAB 50-100 ohms. EGR 65-110 ohms.

TAD & TAB 50-100 ohms.

EGR 65-110 ohms.
06-30-2019, 05:32 PM
Replies: 4
Views: 301
Posted By vjsimone

Also, when in the start position, measure for...

Also, when in the start position, measure for power on all the (disconnected) ICM connector pins.
06-30-2019, 05:15 PM
Replies: 17
Views: 934
Posted By vjsimone

Check the voltage at the TAD & TAB solenoid...

Check the voltage at the TAD & TAB solenoid connectors.
Check the resistance of each vacuum solenoid, with the connector disconnected.
Check the vacuum hoses leading from the TAD & TAB vacuum...
06-30-2019, 04:47 PM
Replies: 17
Views: 934
Posted By vjsimone

With EVP the connector disconnected; Have you...

With EVP the connector disconnected;
Have you checked the continuity/resistance of the EVP Sig wire to the ECA/computer connector?
Also, the SIG RTN/Ground wire ?
06-30-2019, 04:09 PM
Replies: 17
Views: 934
Posted By vjsimone

[QUOTE=minimalist;18731251] When I unplug the...

[QUOTE=minimalist;18731251] When I unplug the vacuum line from the EGR I have no change in idle but I think the idle should increase, shouldn't it? /QUOTE]

I don't believe the EGR operates at...
06-30-2019, 04:05 PM
Replies: 7
Views: 541
Posted By vjsimone

The Army could use a few of those.....

The Army could use a few of those.....
06-30-2019, 04:02 PM
Replies: 4
Views: 234
Posted By vjsimone

Because it's cheap and easy. Fulfills a short...

Because it's cheap and easy. Fulfills a short term Wishful Thinking moment...
06-30-2019, 04:00 PM
Replies: 4
Views: 234
Posted By vjsimone

OBD1 is not going to give you a fault code for a...

OBD1 is not going to give you a fault code for a specific cylinder unless you have a SEFI system.

It will tell you what cylinder engine the computer was calibrated for.

How are you scanning...
Replies: 13
Views: 516
Posted By vjsimone

Maybe one of these ??

Maybe one of these ??
06-20-2019, 09:37 AM
Replies: 9
Views: 656
Posted By vjsimone

Rebuilt or new Distributor ? How do you know...

Rebuilt or new Distributor ?

How do you know the Hall-Effect sensor is new ?

How about the TFI Module ? New/Used ?
Replies: 2
Views: 606
Posted By vjsimone

For a truck that is rarely used, the Ethanol in...

For a truck that is rarely used, the Ethanol in the fuel is going to be an issue. If non-ethanol is available to you, it would be a better choice. ISO HEET is a good product for absorbing the water...
06-18-2019, 09:25 AM
Replies: 9
Views: 656
Posted By vjsimone

(C) 96 - Also, I recommend you replace your Fuel...

(C) 96 - Also, I recommend you replace your Fuel Pump and EEC Relays if they are original.
Showing results 1 to 15 of 500
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.