Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: 94BigRed
Showing results 1 to 15 of 186
Search took 0.31 seconds.
10-10-2013, 09:47 PM
Replies: 1
Views: 869
Posted By 94BigRed

94 460 MAF Conversion

Ok, I know there are a mountain of threads about this, I searched it, 500 posts and nothing I'm looking for. Please don't tell me to search it.

What is the complete list of components and work...
08-31-2012, 11:37 AM
Replies: 12
Views: 646
Posted By 94BigRed

This sounds a lot like what I did to my truck,...

This sounds a lot like what I did to my truck, only it already had a 460 in it, so the swap went pretty smoothly. I assume the big block is fuel injected. Do you plan on bringing in the new ECU,...
07-20-2012, 10:18 AM
Replies: 20
Views: 10,759
Posted By 94BigRed

Honestly, it may be the computer itself. The...

Honestly, it may be the computer itself. The same thing happened to me after I got done building my 94 with a 460. It ran fine for about a month, then started rocketing gas. A new computer has...
07-20-2012, 10:11 AM
Replies: 17
Views: 816
Posted By 94BigRed

I'm getting about 8 in my 94 460. It even has a...

I'm getting about 8 in my 94 460. It even has a D60 on 37s, 5 inch lift. If you do go with a gasser, you should either go carbureted or get one with MAF (mass air flow) fuel injection. These will...
07-20-2012, 09:56 AM
Replies: 14
Views: 21,046
Posted By 94BigRed

The general consensus seemed to be that you don't...

The general consensus seemed to be that you don't need a front sway bar. These new springs are much stiffer and most of the body roll in a turn is in the rear. (the front is initiating it, the rear...
05-18-2012, 09:26 PM
Replies: 6
Views: 849
Posted By 94BigRed

I did the D60 swap in a 94. Make sure you use...

I did the D60 swap in a 94. Make sure you use the mounting plates for the U-bolts and it'll bolt right in.

As far as aluminum crank: what? Did u find one? Because I've never heard of them, but...
05-18-2012, 09:09 PM
Replies: 3
Views: 461
Posted By 94BigRed

I got a pair of Hedmans for my 94 big block. ...

I got a pair of Hedmans for my 94 big block. They fit and work fine and they weren't pricey. They don't have a coating tho, so they need painted or wrapped.

As far as an exhaust system, I'd just...
05-18-2012, 09:00 PM
Replies: 17
Views: 796
Posted By 94BigRed

While this oil leak seems pretty serious right...

While this oil leak seems pretty serious right now, once you get it solved, and it shouldn't be tough, it sounds like you don't have any serious problems. And like BigBlueOx said, with a little work...
05-11-2012, 07:36 PM
Replies: 4
Views: 10,598
Posted By 94BigRed

New seals are cheap and easy to install. And...

New seals are cheap and easy to install. And while they are out, you have a good opportunity to pack the bearings. Thats never a bad idea.
05-07-2012, 09:37 AM
Replies: 2
Views: 616
Posted By 94BigRed

I don't think any body lift would level you. It...

I don't think any body lift would level you. It should lift all the body mounts the same height off the frame front to back. If you try to only lift the front, you'll either need a bunch of shimmed...
05-07-2012, 09:32 AM
Replies: 4
Views: 975
Posted By 94BigRed

Check the fuse in the panel under the hood. I...

Check the fuse in the panel under the hood. I had a wire get rubbed bare and short out my tanks and blew this fuse. I dropped both tanks and swapped switches before I thought to check here.
05-02-2012, 06:46 PM
Replies: 3
Views: 1,111
Posted By 94BigRed

Hmmm... I could see me doing something like...

Hmmm... I could see me doing something like this. But I'd also really benefit from MAF since I bored .030 and have an RV cam.

What engines is this for?
05-02-2012, 06:43 PM
Replies: 8
Views: 414
Posted By 94BigRed

Sometimes u just gotta scare em.

Sometimes u just gotta scare em.
05-02-2012, 03:54 PM
Replies: 8
Views: 414
Posted By 94BigRed

It does sound like a bad bearing or even a bent...

It does sound like a bad bearing or even a bent rim. A bad u-joint would make noise, but it wouldn't make you wobble. You should also make sure the shop you took it to put the wheel on correctly. ...
05-02-2012, 03:45 PM
Replies: 13
Views: 544
Posted By 94BigRed

Unless the 35's are way heavier than the 33's it...

Unless the 35's are way heavier than the 33's it should stay about the same. They shouldn't bog you down too much more than the 33's, and they'll increase your gears ever so slightly. Just do your...
Showing results 1 to 15 of 186
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.