Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: '79BabyBlue
Showing results 1 to 15 of 26
Search took 0.02 seconds.
01-21-2019, 08:00 AM
Replies: 16
Views: 716
Posted By '79BabyBlue

If you have snow or ice on your truck, and a rust...

If you have snow or ice on your truck, and a rust hole in your firewall..it could very easily just be melt off. Baby Blue gets it if conditions are just right.

Check your firewall along that...
01-14-2019, 10:09 PM
Replies: 6
Views: 228
Posted By '79BabyBlue

Warmed up... Not so high. But since I hardly ever...

Warmed up... Not so high. But since I hardly ever go 5 clicks from home.... If I run her a bit and romp the gas pedal at a stop light....she will slow her roll! Hench my 'needs a bathe"
01-14-2019, 09:09 PM
Replies: 6
Views: 228
Posted By '79BabyBlue

Idle set screw is totally an option. I am half...

Idle set screw is totally an option. I am half convinced Grandpa set Baby Blue to run as Grandma drove ...she (Grandma) may or may not have been able to correctly run a stick shift. If your not...
01-14-2019, 08:29 PM
Replies: 6
Views: 228
Posted By '79BabyBlue

High idle?

Soo, when I push the clutch in at a stop sign/light She idils high! Almost scary high...I don't have a tach yet. Sometimes I think she's pushing 3-4?? It's like she wants to run..

Would a good...
01-13-2019, 08:55 AM
Replies: 6
Views: 403
Posted By '79BabyBlue

On my '79 the blower is really quiet, but I can...

On my '79 the blower is really quiet, but I can hear it change speeds. Your vent doors may stuck closed and not actuating with the switch.

I have 2 units that look like this.... under my dash....
01-11-2019, 07:35 PM
Replies: 0
Views: 237
Posted By '79BabyBlue

1979 F150 lift kit

Being in Utah I only have 2 feet of lift "allowance".. measured from frame to ground. I cannot find the original curb specs. Yes, I could and can run a tape measure. But if someone could give me the...
12-20-2018, 05:18 PM
Replies: 7
Views: 473
Posted By '79BabyBlue

Here's a link to the thread I wrote about...

Here's a link to the thread I wrote about removing my '79 F150 heater core and blower motor.

https://www.ford-trucks.com/forums/1562624-heater-core-and-blower-motor-1979-f150-custom.html
12-20-2018, 05:07 PM
Replies: 4
Views: 376
Posted By '79BabyBlue

https://cimg1.ibsrv.net/gimg/www.ford-trucks.com-v...

https://cimg1.ibsrv.net/gimg/www.ford-trucks.com-vbulletin/610x786/1978_fordtruck_pg02_257d3957bc3e2c83a75e5b81453375e7e35f1e39.jpg
I hope this helps. I have a paint chip page also. ...
12-15-2018, 03:49 PM
Replies: 13
Views: 466
Posted By '79BabyBlue

Loose, worn, malfunctioning battery cable...

Loose, worn, malfunctioning battery cable connector? I'm betting negative. Ford's do weird **** without correct juice.

Correction...Ford's do weird **** just cause they can. }> :-missingt
12-06-2018, 08:42 AM
Replies: 2
Views: 225
Posted By '79BabyBlue

Electrical Demons continue

So, on my 1979 F150 custom... I have all lights brake, tail lights, turn signals, markers.... untill I pull on the headlights.

Then; I loose some of the lights. I'm not an electrician.....

Do...
11-21-2018, 12:17 PM
Replies: 14
Views: 503
Posted By '79BabyBlue

Upon closer inspection of your plug.....it does...

Upon closer inspection of your plug.....it does appear something cut off the other side of the plug, and crimped a blade connector on the end, then stuffed it in the hole.

If this is the case,...
11-21-2018, 12:11 PM
Replies: 14
Views: 503
Posted By '79BabyBlue

As for the electrical plug....I hosed the...

As for the electrical plug....I hosed the connection with electrical cleaner. Its an liquid in an aresol can, not the compressed air. Used a tiny screwdriver to GENTLY pull up the tab that holds the...
11-20-2018, 05:55 PM
Replies: 2
Views: 332
Posted By '79BabyBlue

I have not pulled the instrument panel yet. It's...

I have not pulled the instrument panel yet. It's on my to do list to check for loose fittings. I do not know if the other lights work; hubby drove her home with no heater core. So, that along with...
11-19-2018, 06:22 PM
Replies: 11
Views: 378
Posted By '79BabyBlue

I apologise. On second re-read. It WAS about...

I apologise. On second re-read. It WAS about options. Not against my opinion. Sorry. :-X18
11-19-2018, 06:10 PM
Replies: 11
Views: 378
Posted By '79BabyBlue

I was not intending to offend. Just, for me; if...

I was not intending to offend. Just, for me; if your replacing internals with new parts just to keep a date stamp on the outside...it negates the stamp. That being said. I respectfully bow out. :)
Showing results 1 to 15 of 26
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.