Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: crazymut
Showing results 1 to 15 of 500
Search took 0.55 seconds.
03-22-2019, 01:54 PM
Replies: 7
Views: 206
Posted By crazymut

Bought new OEM ICP, installed, cleared codes, now...

Bought new OEM ICP, installed, cleared codes, now need to complete test monitor drive cycle. BTW, it's a 3/4 in. wrench,socket
03-22-2019, 12:37 PM
Replies: 7
Views: 206
Posted By crazymut

Yes there is oil on/in the plug

Yes there is oil on/in the plug
03-22-2019, 11:35 AM
Replies: 7
Views: 206
Posted By crazymut

It's running fine. Cleared codes last night and...

It's running fine. Cleared codes last night and it's back this morning after two drive cycles
03-22-2019, 11:02 AM
Replies: 7
Views: 206
Posted By crazymut

code 1280

Pulled code 1280 on my truck, ICP out of range (low). Does this mean the switch is bad?
03-22-2019, 10:50 AM
Replies: 0
Views: 138
Posted By crazymut

code 1280

Pulled code 1280 on my truck, ICP out of range (low). Does this mean the switch is bad?
01-29-2019, 09:45 PM
Replies: 8
Views: 333
Posted By crazymut

It was definitely from the knuckle. Nothing above...

It was definitely from the knuckle. Nothing above was wet. Did check diff vent line and found it plugged with a spider nest. Cleared, drove in four wheel for about a mile, not leaking any oil anymore.
01-27-2019, 09:28 PM
Replies: 8
Views: 333
Posted By crazymut

Leak on left front axle

Are leaks in the front drive shaft common? Hard to fix? Was fine and today I had to put it into 4x4 for about 30 yards. Got home and noticed left front axle was wet. Wet enough to have sprayed some...
11-03-2018, 01:35 PM
Replies: 2
Views: 250
Posted By crazymut

Dana 60 Ordered through Tasca

Dana 60 Ordered through Tasca
11-02-2018, 05:43 PM
Replies: 2
Views: 250
Posted By crazymut

Front drive shafts

Does anyone need drive shafts for 2001 F250? Getting ready to send some back. I didnít need them. I can ship them quicker than vendor since I have them. Pay what I paid and shipping. New in box.
11-01-2018, 01:33 PM
Replies: 9
Views: 465
Posted By crazymut

Got it fixed. The needle bearings were going out....

Got it fixed. The needle bearings were going out. Replaced hubs, brakes and vacuum lines. Shafts were not damaged. Made my hunting trip, got skunked due to passing on average deer. Stopped for diesel...
10-16-2018, 09:21 PM
Replies: 9
Views: 465
Posted By crazymut

I ordered new shirt and long shaft assemblies...

I ordered new shirt and long shaft assemblies with new u-joints and new hubs. Hubs showed up today. May remove old hubs to see if short shaft is still good and just put on the new hubs. New shafts...
10-12-2018, 03:07 PM
Replies: 9
Views: 465
Posted By crazymut

Thanks Denny. Getting ready for hunting trip and...

Thanks Denny. Getting ready for hunting trip and this pops up.
10-12-2018, 01:31 PM
Replies: 9
Views: 465
Posted By crazymut

I was figuring something like that. Is it easier...

I was figuring something like that. Is it easier to just replace the hub?
10-12-2018, 12:51 PM
Replies: 9
Views: 465
Posted By crazymut

Right hub

Noticed lately when driving my truck i get a noise almost like a tire rubbing on the plastic fender liners.That's not what it is. It happens when I make slight right turns, i.e. following the curve...
02-18-2017, 02:23 PM
Replies: 337
Views: 28,724
Posted By crazymut

Haven't been on in a while, just saw the sad...

Haven't been on in a while, just saw the sad news. RIP brother. Your posts were ones that I'd always read and look to for advice. You will be missed.
Showing results 1 to 15 of 500
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.