Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: airharley
Showing results 1 to 15 of 499
Search took 0.83 seconds.
01-26-2017, 03:59 PM
Replies: 11
Views: 864
Posted By airharley

I really liked my trucks MPG with a 351W. Almost...

I really liked my trucks MPG with a 351W. Almost everything will cross over to it from the 302 including the AOD.
02-17-2016, 07:32 PM
Replies: 10
Views: 1,966
Posted By airharley

Make sure that the gasket material doesn't absorb...

Make sure that the gasket material doesn't absorb or retain water or attract dirt. Too many times I've seen good intentions with temporary gasket material left in and rotted the bed sheet metal.
02-17-2016, 07:20 PM
Replies: 321
Views: 80,026
Posted By airharley

I see you also sell them on evilbay, 377sb2. How...

I see you also sell them on evilbay, 377sb2. How many do you normally make in a production run? We recently purchased a 03 Exped in need of the replacement gear. It isn't a priority yet but I'd like...
04-08-2014, 11:15 PM
Replies: 13
Views: 1,408
Posted By airharley

I found some on ebay that may be something you...

I found some on ebay that may be something you are looking for. Or you can go over to mustangs unlimited Mustangs Unlimited - The Premier Source for Mustang, Shelby and Cougar Parts and Accessories...
04-05-2014, 11:58 PM
Replies: 13
Views: 1,408
Posted By airharley

The spring prevents the hose from collapsing as...

The spring prevents the hose from collapsing as the pump can suck the hose shut. I know it is a major pain at times but if you take out the spring chances are you'll overheat and not see a reason for...
04-05-2014, 01:10 PM
Replies: 18
Views: 1,183
Posted By airharley

You can also add a plate with cut outs similar to...

You can also add a plate with cut outs similar to this crude design to keep using what you have [<> <>] If you weld all around the the plate, inside and out that will make it stronger. Or you can cut...
04-05-2014, 12:57 PM
Replies: 2
Views: 760
Posted By airharley

The rear may be a 9 1/2". Look for a turned down...

The rear may be a 9 1/2". Look for a turned down right corner on the upper horizontal rib of the third member. There is nothing wrong with it IF you do not plan to modify it except for the coil to...
04-05-2014, 12:50 PM
Replies: 27
Views: 2,470
Posted By airharley

I would IF I didn't have a client in from the...

I would IF I didn't have a client in from the East Coast. I wouldn't mind spending a day picking the brains of the younger crowd to see what they like and don't like. If my son is any indication, it...
11-11-2012, 06:13 PM
Replies: 4
Views: 727
Posted By airharley

fresh air vent door seal

So this weekend I opted to see how hard it would be to rebuild the door flap seals on the kick panel vents. As it turns out, it is super simple to change them out. The hardest part I believe is...
10-14-2012, 11:23 PM
Replies: 5
Views: 1,558
Posted By airharley

After the first full heating cycle you need to...

After the first full heating cycle you need to re-torque all the intake manifold hardware to make sure you don't have seal leaks.
10-14-2012, 11:14 PM
Replies: 6
Views: 1,757
Posted By airharley

You can also get them from any spring repair...

You can also get them from any spring repair shop. I grabbed them for a lot less then repos from Mac's and also picked up the other misc parts needed like new perch centering bolt.
10-14-2012, 11:09 PM
Replies: 4
Views: 928
Posted By airharley

Check the upper bearing just under the turn...

Check the upper bearing just under the turn signal switch to make sure it isn't from there. Another possible source is the switch itself.
10-14-2012, 11:00 PM
Replies: 2
Views: 366
Posted By airharley

You can search for "AOD behind 460" to pull up...

You can search for "AOD behind 460" to pull up several google results to see the adapters used to mate one. The other problem with going to a AOD is the amount of upgrades you will need to perform to...
10-14-2012, 10:48 PM
Replies: 2
Views: 967
Posted By airharley

Finding a donor with the other areas besides the...

Finding a donor with the other areas besides the ones you need rotted out. I had to make my own patches out of 16 ga steel then hand massaging them to fit. It sucks but it is worth the effort in the...
10-14-2012, 10:34 PM
Replies: 7
Views: 626
Posted By airharley

Easiest way to remove the accessories you don't...

Easiest way to remove the accessories you don't want is to convert to an all serpentine drive system from March or Zoop. If V-belts are your flavor, then you may have to change the water pump, timing...
Showing results 1 to 15 of 499
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.