Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: baddad457
Showing results 1 to 15 of 500
Search took 0.61 seconds.
Replies: 8
Views: 545
Posted By baddad457

I don't think a 351M/400 pan will fit a 351C's...

I don't think a 351M/400 pan will fit a 351C's rear main bearing cap. The 351M/400 had half inch larger main journals as I recall. Same deal with the 302-351W's, pans aren't interchangeable.
Yesterday, 08:49 PM
Replies: 24
Views: 559
Posted By baddad457

Caps and rotors don't last 4-5 years, not even...

Caps and rotors don't last 4-5 years, not even the brass terminal ones. They should have been replaced with the plugs and wires.
Yesterday, 08:43 PM
Replies: 24
Views: 559
Posted By baddad457

Remove the driver's side valve cover, then one...

Remove the driver's side valve cover, then one rocker arm. Then pull the pushrod out and measure it. Roller cam 351 pushrods are 7.567 inches long. Flat tappet engines are about a half inch longer....
Yesterday, 08:35 PM
Replies: 24
Views: 559
Posted By baddad457

Never ever seen a stock Ford distributor with a...

Never ever seen a stock Ford distributor with a bronze gear.
Yesterday, 06:43 AM
Replies: 6
Views: 267
Posted By baddad457

Find a small mom and pop shop that's been in...

Find a small mom and pop shop that's been in business a long time. Stay away from the large, chain shops
Yesterday, 06:39 AM
Replies: 37
Views: 3,526
Posted By baddad457

Damn you're full of yourself. You need help

Damn you're full of yourself. You need help
06-23-2019, 10:17 PM
Replies: 37
Views: 3,526
Posted By baddad457

I never said I did. Show me where I did. You need...

I never said I did. Show me where I did. You need help in reading comprehension bubba. I can see why you're confused.
Replies: 18
Views: 447
Posted By baddad457

:confused: Why would I ?

:confused: Why would I ?
Replies: 18
Views: 447
Posted By baddad457

I never mounted either pump on rubber bushings...

I never mounted either pump on rubber bushings and like I said before, neither are noisy. These are the small square electrics, not the high performance ones you'd pick for drag racing. You can't...
06-23-2019, 11:09 AM
Replies: 37
Views: 3,526
Posted By baddad457

Damn, talk about pot calling the kettle black....

Damn, talk about pot calling the kettle black. Why not go back through this thread and READ what was posted before making a fool of yourself here.
Replies: 9
Views: 615
Posted By baddad457

Sounds like a carb tuning problem to me, possibly...

Sounds like a carb tuning problem to me, possibly not idled high enough or rich enough. Could also be timing retarded too much.. If it was a vacuum leak, just the way it would be noticeable while...
Replies: 6
Views: 418
Posted By baddad457

The tricky part is getting the oiling holes...

The tricky part is getting the oiling holes aligned with the block. And installing them in the correct location. There were different bearing sets for the center oiler and side oiler. The side oiler...
06-23-2019, 09:06 AM
Replies: 6
Views: 267
Posted By baddad457

Not wanting to return to center is either caster...

Not wanting to return to center is either caster or camber's off ( don't recall which )
06-23-2019, 08:53 AM
Replies: 37
Views: 3,526
Posted By baddad457

Being silly ? Nope.

Being silly ? Nope.
Replies: 18
Views: 447
Posted By baddad457

Neither I ran are noisy at all. You can barely...

Neither I ran are noisy at all. You can barely hear either with the key on and the engine off.
Showing results 1 to 15 of 500
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.