Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: LCAM-01XA
Showing results 1 to 15 of 494
Search took 0.53 seconds.
04-06-2012, 03:18 AM
Replies: 5
Views: 1,358
Posted By LCAM-01XA

Power steering pump w/ pulley, its mounting...

Power steering pump w/ pulley, its mounting bracket and the aluminum spacer behind it, and the pressure hose between the pup and the steering box if possible - basically cut the belt, cut the low...
04-05-2012, 03:28 PM
Replies: 10
Views: 3,514
Posted By LCAM-01XA

Really now, then I suppose it's the Jedi Force...

Really now, then I suppose it's the Jedi Force holding my E4OD converter to the engine crank? Cause what I got in there is exactly like the flywheel the OP posted... just sayin'!

To the OP - as...
04-05-2012, 03:00 PM
Replies: 101
Views: 16,643
Posted By LCAM-01XA

2.5k will shoot ya up in the 200F range, too high...

2.5k will shoot ya up in the 200F range, too high IMHO -if ya want to mimic more than 160F go with something like 4k, that should be around 170 or so... And yah, you'll have to clip the two wires and...
04-05-2012, 02:51 PM
Replies: 101
Views: 16,643
Posted By LCAM-01XA

5k (5000) ohm resistor should do the trick based...

5k (5000) ohm resistor should do the trick based on the info posted above, it should make the PCM think you're at like 160F all the time.

Not sure if a failing TFT will cause a gear skip...
02-28-2012, 02:45 PM
Replies: 44
Views: 22,459
Posted By LCAM-01XA

Two questions: 1) I see you laid the pump on...

Two questions:

1) I see you laid the pump on its side, I thought they are supposed to be mounted upright?

2) In this picture your coolant filter is plumbed so it receives the full flow through...
02-28-2012, 02:25 PM
Replies: 99
Views: 56,239
Posted By LCAM-01XA

Aha! So I was correct in that the difference in...

Aha! So I was correct in that the difference in positions between vacuum and hydro boosters is still the same in the OBS trucks as it was in the bricknoses, and that Ford accounts for it with by...
02-28-2012, 02:16 PM
Replies: 99
Views: 56,239
Posted By LCAM-01XA

Well that ain't right, you should have at least...

Well that ain't right, you should have at least one washer, the one that goes between BOO switch and the retaining clip - the idea is to firmly sandwich the BOO switch in place on the pin so that its...
02-28-2012, 03:05 AM
Replies: 99
Views: 56,239
Posted By LCAM-01XA

Ya know, it seems like for every 3 people that...

Ya know, it seems like for every 3 people that say you absolutely need the hydroboost-specific pedal to make everything operate like it should there is at least one person who claims they run the...
02-28-2012, 02:25 AM
Replies: 99
Views: 56,239
Posted By LCAM-01XA

Your booster pushrod is anything but level right...

Your booster pushrod is anything but level right now - not only is it angled downwards because of how much lower its pin is on your non-hydroboost pedal (compared to a hydroboost-specific pedal),...
02-18-2012, 04:24 AM
Replies: 99
Views: 56,239
Posted By LCAM-01XA

So is the hole for the pedal pin off-center on...

So is the hole for the pedal pin off-center on the pushrod somehow, or what? The FSGM setup you can slide it on either way, it's perfectly symmetrical... Leave it to Ford to screw up a simple...
11-09-2011, 11:50 PM
Replies: 43
Views: 15,777
Posted By LCAM-01XA

Well I've never had one go poof on me, but from...

Well I've never had one go poof on me, but from what I've heard if the converter is on its way out there will be other signs of it as well, odd sounds at idle from the bellhousing area comes to mind...
11-09-2011, 09:23 PM
Replies: 43
Views: 15,777
Posted By LCAM-01XA

Oh, don't get the wrong idea, I'm only dropping...

Oh, don't get the wrong idea, I'm only dropping by to share my E4OD-related scares, and thus hopefully help someone not toast their trans or sell their truck out of desperation or something - I still...
11-09-2011, 08:21 PM
Replies: 21
Views: 1,696
Posted By LCAM-01XA

Hour-meters are nice, but may not be quite as...

Hour-meters are nice, but may not be quite as useful as you may think - for instance I know folks who put theirs in as part of the key-on accessory circuits, and those same individuals then proceed...
11-09-2011, 08:08 PM
Replies: 21
Views: 1,696
Posted By LCAM-01XA

Another use for high idle - whenever we travel...

Another use for high idle - whenever we travel cross-country in either of the diesel-powered trucks we never shut off the engine, this usually means way over 24 hours of non-stop run time, many of...
11-09-2011, 07:56 PM
Replies: 43
Views: 15,777
Posted By LCAM-01XA

As per info Mark posted as a reply to a question...

As per info Mark posted as a reply to a question of mine a while back, it seems the PCM monitors converter input speed through the engine speed sensor, and the converter output speed through the VSS...
Showing results 1 to 15 of 494
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.