Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: aawlberninf350
Showing results 1 to 15 of 500
Search took 0.39 seconds.
Yesterday, 10:09 PM
Replies: 10
Views: 450
Posted By aawlberninf350

Is that the Glenfiddich talking? :-partybud ...

Is that the Glenfiddich talking? :-partybud

Always wanted to use that emoji.

Is Mercon V synthetic?
Yesterday, 10:00 PM
Replies: 13
Views: 514
Posted By aawlberninf350

Good call on the new harmonic balancer. They die...

Good call on the new harmonic balancer. They die when the rubber goes bad. Otherwise indestructible.

I'd only use the RTV to hold the key in place. If the keyway is facing up, and the key stays...
Yesterday, 09:42 PM
Replies: 10
Views: 140
Posted By aawlberninf350

Problem is likely not enough lube on the caliper...

Problem is likely not enough lube on the caliper slide pins. When they stick, they drag. Or collapsing hoses.

I've used Power Stop calipers on other applications, no issues. Just a rebuild with...
Yesterday, 09:29 PM
Replies: 1
Views: 57
Posted By aawlberninf350

Welcome to FTE! Crack a cold one (unless you're...

Welcome to FTE! Crack a cold one (unless you're into sake) and stay a while.

A failing starter can do that. Once it's hot it doesn't work as well.

First would be good to check the system...
Yesterday, 09:18 PM
Replies: 4
Views: 86
Posted By aawlberninf350

I think the fuse Mark pointed to is #12 on the...

I think the fuse Mark pointed to is #12 on the fuse panel, if your 03 is like my 02. Also pull the fuel heater wire off the back of the fuel bowl, replace the fuse, but do not replace the wire. A...
Yesterday, 08:44 PM
Replies: 6
Views: 211
Posted By aawlberninf350

Sounds like water getting past a bad windshield...

Sounds like water getting past a bad windshield seal to me too.

Get it out of the rain, remove the fuse box cover, and hang a hairdrier off the steering wheel aimed at the fuse panel. Leave the...
Yesterday, 01:40 AM
Replies: 8
Views: 413
Posted By aawlberninf350

Take the Ford part back and see if you can get a...

Take the Ford part back and see if you can get a refund. Should not blow out like that.

FWIW my pressure side hose is whatever they had on hand at O'Reilly's. No issues.
Yesterday, 01:28 AM
Replies: 20
Views: 1,139
Posted By aawlberninf350

I have that same 15k Reese hitch, works fine....

I have that same 15k Reese hitch, works fine. Best to slide back before you think you need to, otherwise a long day on the road with not enough sleep may result in dentage of the cab corners. Ask me...
Yesterday, 12:40 AM
Replies: 16
Views: 404
Posted By aawlberninf350

Great story and pics, thanks! Gonna do the...

Great story and pics, thanks!

Gonna do the oil pan proper style? Upside down etc?
Yesterday, 12:33 AM
Replies: 9
Views: 312
Posted By aawlberninf350

Another thumbs up on WeatherTech mats. I have the...

Another thumbs up on WeatherTech mats. I have the floor liner version, front and rear. Not cheap but the fit is great and they provide a lot of protection. Get what you pay for.
Yesterday, 12:27 AM
Replies: 4
Views: 220
Posted By aawlberninf350

I'm thinking more like u joint or carrier...

I'm thinking more like u joint or carrier bearing. Yank the drive shaft around a bit and see if things look loose.
06-23-2019, 07:45 PM
Replies: 10
Views: 450
Posted By aawlberninf350

Same here with the reverse delay, it's normal as...

Same here with the reverse delay, it's normal as far as I know. It did not change when I installed the Factory Tech valve body, or with tunes. Our Subie has a similar delay shifting into drive. Go...
06-23-2019, 04:29 AM
Replies: 69
Views: 6,312
Posted By aawlberninf350

Good days work there! Kudos! By the grace...

Good days work there! Kudos! By the grace afforded to me, I reaffirm your right to vote.

FWIW, wife is too good for you. Don't forget.

Lincoln above looks familiar. I pumped a few 30-30 rounds...
06-23-2019, 04:11 AM
Replies: 4
Views: 238
Posted By aawlberninf350

Exhaust back pressure sensor can get clogged with...

Exhaust back pressure sensor can get clogged with soot. Remove and clean carefully with a wood tool or similar since the membrane up in there can be damaged. Use a wrench above and below to remove...
06-23-2019, 03:56 AM
Replies: 12
Views: 332
Posted By aawlberninf350

What manual locking hubs did you get? Good...

What manual locking hubs did you get?

Good idea to inspect the needle bearings inside the hub to check for damage on the stub axle when you install the manual hubs. They can be lubed if they still...
Showing results 1 to 15 of 500
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.