Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: atccracing
Showing results 1 to 15 of 196
Search took 0.59 seconds.
03-23-2011, 09:04 PM
Replies: 226
Views: 158,742
Posted By atccracing

The Need for the 79 pressure line is because...

The
Need for the 79 pressure line is because of the smaller fitting.
03-23-2011, 08:38 PM
Replies: 9
Views: 329
Posted By atccracing

Are your backing plates rotted away? If they are...

Are your backing plates rotted away? If they are that may cause the inside of the rotor issue.
03-20-2011, 08:47 AM
Replies: 5
Views: 414
Posted By atccracing

With the heat, easy out, and a bit of luck, it...

With the heat, easy out, and a bit of luck, it should come right out.
03-20-2011, 08:11 AM
Replies: 13
Views: 10,394
Posted By atccracing

Don't take it personally, some believe its a sin...

Don't take it personally, some believe its a sin to go anyway but up!
03-19-2011, 06:46 AM
Replies: 5
Views: 1,080
Posted By atccracing

That would be a good place to start. Do you have...

That would be a good place to start. Do you have a manual? I'd test the circuit before throwing a part at it.
03-19-2011, 06:40 AM
Replies: 13
Views: 9,428
Posted By atccracing

That would do it. Goodluck with the new engine!

That would do it. Goodluck with the new engine!
03-19-2011, 06:35 AM
Replies: 32
Views: 58,554
Posted By atccracing

I have a Rough Country 4 with 33's with blocks,...

I have a Rough Country 4 with 33's with blocks, looks great and rides good. Like stated make sure you get EVERYTHING you need not just what the kit comes with. I ended up buying extra parts (would...
03-17-2011, 03:23 PM
Replies: 14
Views: 4,592
Posted By atccracing

I took the old EGR, cut the base off, welded the...

I took the old EGR, cut the base off, welded the hole closed, now its just a flat block off plate.

Now I have to work on the CEL. Not sure if I'll try to make the resistor plug or buy them, or...
03-14-2011, 09:33 PM
Replies: 55
Views: 24,078
Posted By atccracing

I've got 4" with 33's. Had to put a heavy duty PS...

I've got 4" with 33's. Had to put a heavy duty PS pump to turn during parking. Also had to install adjustable ball joints to get the camber right. That said, she looks great, and rides well. I do...
03-13-2011, 06:09 PM
Replies: 13
Views: 10,338
Posted By atccracing

I just finished installing my hedman long tubes...

I just finished installing my hedman long tubes custom 2.5 y pipe, made from some mandrel bent U tubes cut and welded into a magna flow Y. Magnaflow cat & Summit SI/SO 3". It was MUCH cheaper!...
03-13-2011, 05:56 PM
Replies: 4
Views: 10,227
Posted By atccracing

Good info thanks.

Good info thanks.
03-13-2011, 05:35 PM
Replies: 34
Views: 24,360
Posted By atccracing

Well I was on Comp cams today and the retro fit...

Well I was on Comp cams today and the retro fit pushrods I think are probably the right length If I've done my math correctly(adding the excessive clearance and a bit more for pre load). So this may...
03-13-2011, 07:12 AM
Replies: 10
Views: 10,388
Posted By atccracing

I just installed a Summit 3 inch exhaust, its got...

I just installed a Summit 3 inch exhaust, its got good tone & is on the quiet side. I also have a cat though, the will keep it a little quieter.
03-12-2011, 08:03 PM
Replies: 3
Views: 9,928
Posted By atccracing

Yes. Your probably right.

Yes. Your probably right.
03-12-2011, 08:01 PM
Replies: 4
Views: 10,227
Posted By atccracing

Isn't there always! I thinking I might need...

Isn't there always! I thinking I might need longer pushrods. Need to know how to check exactly how long.
Showing results 1 to 15 of 196
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.