Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: keisha9
Showing results 1 to 15 of 273
Search took 0.57 seconds.
Replies: 5
Views: 470
Posted By keisha9

A

Alright so 7/16ths thru the filter to pump hole from both sides. Correct? And for the the main bearing saddle, is it the block or the race that gets worked?
Replies: 5
Views: 470
Posted By keisha9

Oiling mods. Yes or no ..428

Are the block oiling mods a must ? I know there is the oil filter area and the bearing area as well...428 fe street cruiser/driver...... thx
Replies: 5
Views: 626
Posted By keisha9

I found some more just not the exact 2287 . Guess...

I found some more just not the exact 2287 . Guess I'll need a set or try to match 1 .
Replies: 5
Views: 626
Posted By keisha9

Yeah there is a big seller that has cast sets on...

Yeah there is a big seller that has cast sets on ebay. Just don't know if its legit. I didn't realize they don't sell the cast anymore! I guess forged is heavily available but didn't want to go that...
Replies: 5
Views: 626
Posted By keisha9

Need 428 piston @ 4.16 bore

Is there any 428 cast pistons available 30 over? I had a 2287p piston break. Seems no longer available.
Replies: 8
Views: 1,233
Posted By keisha9

https://cimg3.ibsrv.net/gimg/www.ford-trucks.com-v...

https://cimg3.ibsrv.net/gimg/www.ford-trucks.com-vbulletin/2000x1124/80-14941790457002130173329_4f6a4d5c4f93b88067cd40e56c5f6c8a72196933.jpg
It had broken a pump shaft . Rebuilt already. I got it...
Replies: 8
Views: 1,233
Posted By keisha9

Torque to 100ft lb and call it a day or do I need...

Torque to 100ft lb and call it a day or do I need to plastiguage or ........
Replies: 8
Views: 1,233
Posted By keisha9

Acquired a 390. Check bearings??

I just acquired a 390 . I want to verify main bearings are ok before installing. Should I pull 1 cap or all? Can I torque back to 100ft lb and be ok. Should I pull a certain one first? Should I check...
Replies: 12
Views: 1,837
Posted By keisha9

Block is at machine shop right now. Just found a...

Block is at machine shop right now. Just found a crank. I'm going to need to find rods and pistons. Any body have any ? Is the 8594 going good to hurt me that bad?
Replies: 12
Views: 1,837
Posted By keisha9

Help me! 390 build parts

I'm having a 390 built from a 360. I need to buy parts. Right now I have full msd with mechanical distributor.
Switching to rpm intake from the sp2p. Switching from edelbrock 750 cfm to a smaller...
02-06-2017, 08:37 PM
Replies: 2
Views: 357
Posted By keisha9

What springs for ifs

Looking for a recommendation for springs from heidts for mustang ii ifs. 375 lb or 425 lb. Engine is a 390fe and iron heads ...also looking for decent shocks, but not to fancy . What are you...
02-01-2017, 10:05 AM
Replies: 6
Views: 959
Posted By keisha9

john, I like your design and seems to make the...

john, I like your design and seems to make the most sense. I think I'll be doing this also for peice of mind..
01-31-2017, 10:00 PM
Replies: 6
Views: 959
Posted By keisha9

Thanks for replying. That is exactly what I'm...

Thanks for replying. That is exactly what I'm talking about or like this one that I found on the Web. I'm installing heidts and want it as strong as possible. The tube that's included with the little...
01-31-2017, 02:26 PM
Replies: 6
Views: 959
Posted By keisha9

Heidts mustang II. LCA question

If you use a tubular lower control arm is it advisable to make a rear mount off of the frame with 2 bolts so u have 2 mounting points?
Replies: 0
Views: 363
Posted By keisha9

What engine mounts r these

What vehicle are these F.E. mounts from? Do they go on the smaller 2 of the 4 holes?
...
Showing results 1 to 15 of 273
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.