Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: Ford F834
Showing results 1 to 15 of 499
Search took 0.38 seconds.
10-16-2018, 12:33 AM
Replies: 2,196
Views: 602,730
Posted By Ford F834

No, I have a set of factory turbo rods that are...

No, I have a set of factory turbo rods that are going in. My pistons are ceramic coated but not cut. The engine isn’t built yet so I don’t know what the protrusion will be, but it is whatever Mahale...
10-16-2018, 12:03 AM
Replies: 2,196
Views: 602,730
Posted By Ford F834

The engine with the crumpled rods was stock...

The engine with the crumpled rods was stock compression. Rod failure is the result of excessive peak cylinder pressures. Factors that influence peak cylinder pressure include: static compression...
Replies: 8
Views: 1,488
Posted By Ford F834

If they are the type the trim the very edge of...

If they are the type the trim the very edge of the wheel opening, then they are fastened with screws to the lip of the fender. If they are the type of wheel arch molding that is slightly above the...
Replies: 9
Views: 889
Posted By Ford F834

Yeah, unfortunately KY is indeed quite a hike...

Yeah, unfortunately KY is indeed quite a hike from here... I just don't have the tools or knowledge to correctly set up gears, and I've read enough horror stories about guys who ~thought they could...
Replies: 9
Views: 889
Posted By Ford F834

Where are you located? Do you have the gear sets...

Where are you located? Do you have the gear sets removed or are they still in the axles? I have 4.10's and would like to go to 3.55, but I am NOT interested in re-gearing. Whole axle swap only. My...
Replies: 5
Views: 591
Posted By Ford F834

1980-1984 had rosewood. There was never any such...

1980-1984 had rosewood. There was never any such thing as burlwood door trim. 1985-1986 high end door panels had cloth inserts instead. The rosewood door panels are hard to find. I have a spare...
Replies: 9
Views: 808
Posted By Ford F834

How about a metallic grey/silver that meshes with...

How about a metallic grey/silver that meshes with the other silver accents on the truck and then paint new pin stripes (black?). Pin stripe on a rim is really easy with a fine brush since you can...
Replies: 18
Views: 1,041
Posted By Ford F834

I don't want to put down any of the above advice,...

I don't want to put down any of the above advice, as I have not specifically tried denatured alcohol, or any of the other waxes or polishes mentioned. However I would caution that alcohols do not...
Replies: 11
Views: 636
Posted By Ford F834

If you are simulating a stock short bed then yes....

If you are simulating a stock short bed then yes. Just remove 16" ahead of the axle. But there are certainly other ways to custom shorten a bed, ahead of the axle, behind the axle or a combination of...
Replies: 11
Views: 636
Posted By Ford F834

There are dozens of you tube videos on lb to sb...

There are dozens of you tube videos on lb to sb conversions, this guy did a nice clean job of shortening the box on a '65 Chevy. You might like this if you are going that route vs. finding a stock...
Replies: 11
Views: 636
Posted By Ford F834

Hole spacing was perfect on mine. After deleting...

Hole spacing was perfect on mine. After deleting 16" behind the forward bed mount holes all 8 dropped into place on the short bed.
Replies: 18
Views: 1,041
Posted By Ford F834

If you end up purchasing this bezel and want to...

If you end up purchasing this bezel and want to restore the chrome edging and chrome nameplate lettering you might find post #23 on my F150 build thread to have some helpful tips. Best of luck and...
Replies: 18
Views: 1,041
Posted By Ford F834

I have seen these come along on eBay from time to...

I have seen these come along on eBay from time to time, but they are few and far between.
Replies: 11
Views: 636
Posted By Ford F834

I have a write up on my long bed to short bed...

I have a write up on my long bed to short bed frame chop in my build thread. Mine is a crew cab, but I've been looking at chopping my F150 and it is pretty much identical. The first few posts in my...
Replies: 81
Views: 3,020
Posted By Ford F834

2019 GTG at the Bonneville salt flats? Justin...

2019 GTG at the Bonneville salt flats? Justin tells me my engine should make ~900 ft lbs of torque at the rear wheels and my final gearing will be 2.52. The DB4 has no rev limiter and will spin to...
Showing results 1 to 15 of 499
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.