Ford Truck Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: biasvoltage
Showing results 1 to 15 of 30
Search took 0.02 seconds.
06-14-2019, 06:18 PM
Replies: 8
Views: 382
Posted By biasvoltage

The dash light is for the low brake fluid warning...

The dash light is for the low brake fluid warning sensor on the proportioning valve block, there is no warning lamp for the parking brake being on (at least not on my '74 F250)
06-10-2019, 10:29 PM
Replies: 10
Views: 792
Posted By biasvoltage

You could get a dual channel speaker from Custom...

You could get a dual channel speaker from Custom Autosound or the like, and put that in the dash location. Presumably your new head unit has provisions for 4 speakers, run the front outputs to the...
06-07-2019, 12:43 PM
Replies: 17
Views: 1,073
Posted By biasvoltage

They are 16" 8 lug van wheels, so 16x7.

They are 16" 8 lug van wheels, so 16x7.
06-07-2019, 12:32 PM
Replies: 26
Views: 1,381
Posted By biasvoltage

NumberDummy, does any of your reference material...

NumberDummy, does any of your reference material indicate torque values, or whether the truck should be on the ground or in the air, when installing that particular sway bar? I've looked at the...
06-06-2019, 09:17 AM
Replies: 26
Views: 1,381
Posted By biasvoltage

When you say "pulled", do you mean pulled towards...

When you say "pulled", do you mean pulled towards the front, pulled towards the back, or removed it entirely?
06-05-2019, 07:48 PM
Replies: 17
Views: 1,073
Posted By biasvoltage

I picked up a set of 16" 8 lug wheels from a...

I picked up a set of 16" 8 lug wheels from a 1990s Econoline van at the salvage yard for $10 a piece, cleaned them up and sprayed a couple coats of Duplicolor Wimbledon white on them. I put on a...
05-27-2019, 12:02 PM
Replies: 26
Views: 1,381
Posted By biasvoltage

I've got this same sway bar - has anyone seen any...

I've got this same sway bar - has anyone seen any published information about how to adjust this primitive version of the sway bar? There is no image or mention of it in the 1974 Chassis shop...
05-20-2019, 09:15 PM
Replies: 1
Views: 176
Posted By biasvoltage

73-74 F250 Sway Bar help

Hello - I'm wrapping up my front end refresh on my 1974 F-250 (8100GVW suspension). The sway bar is the early version that mounts between the radius rods, as in the picture below. There is...
05-14-2019, 09:00 PM
Replies: 23
Views: 1,163
Posted By biasvoltage

so instead of using current to light up an...

so instead of using current to light up an incandescent bulb, you turn the same amount into heat using a resistor - what then, do you gain by using the LED bulbs?
05-12-2019, 08:27 PM
Replies: 5
Views: 346
Posted By biasvoltage

Best bet is a fuel pressure regulator. I bought...

Best bet is a fuel pressure regulator. I bought a Summit branded one and it leaked, they sent another and it leaked too so I picked up a Holley branded one. Rock steady pressure, no leaks, I set...
05-08-2019, 10:55 AM
Replies: 12
Views: 1,039
Posted By biasvoltage

I'd agree with meangreen - this sounds like a...

I'd agree with meangreen - this sounds like a grounding issue as opposed to a short.
04-25-2019, 08:26 PM
Replies: 10
Views: 363
Posted By biasvoltage

I just went through this, no pre-bent kit...

I just went through this, no pre-bent kit available for my 1972 F250 2wd long bed. Made my own, using 3/16" Nicopp line and a Titan 3/16" double flaring tool, which was worth every penny of the 50...
04-19-2019, 12:27 PM
Replies: 60
Views: 3,433
Posted By biasvoltage

Knocking - I hate to envision a bad scenario, but...

Knocking - I hate to envision a bad scenario, but is it possible that something fell in one of the spark plug holes, or one of the old spark plugs lost a sliver of insulator or an electrode when you...
04-14-2019, 09:31 PM
Replies: 9,894
Views: 916,595
Posted By biasvoltage

Finished up my brake line replacement that I...

Finished up my brake line replacement that I started last weekend, nicopp replacing all of the steel lines. Nicopp is great to work with! All new rubber brake flex hoses as well. Replaced all 4...
04-14-2019, 07:34 PM
Replies: 11
Views: 372
Posted By biasvoltage

My truck has a master cylinder and a separate...

My truck has a master cylinder and a separate proportioning valve, and there were a couple of hard to find sizes on them for the flare nut connections. I found this kit on Amazon that had...
Showing results 1 to 15 of 30
 


 
Forum Jump

Contact Us - About Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.